- Forest Products:
- 687 (PIN: 4FZ1-UP)
- 570 (PIN: 4XR1-UP)
- 495 (PIN: 5TZ1-UP)
- 487 (PIN: 6KW1-UP)
- 580 (PIN: 7CN1-UP)
- 550 (PIN: 7ZN1-UP)
- 695 (PIN: 8MW1-UP)
- 570 (PIN: 4XR1-UP)
Introduction
This Special Instruction provides the necessary information that is required to install the 159-3693 Cab Visors on the machines that are listed above.
There are four sun visors that need to be mounted inside the operator's compartment. The 174-7346 Visor is mounted horizontally on the front window. The 174-7348 Visor is mounted horizontally on the rear window. The 174-7347 Visor is mounted vertically on the left window. The 174-7349 Visor is mounted vertically on the right window.
Do not perform any procedure that is outlined in this publication, until you understand the information that is contained in this document. Do not order parts until you understand the information that is contained in this document.
Installation Procedure for the 159-3693 Cab Visors Kit
Parts List for 159-3693 Cab Visor Kit     | |||
Item     | Quantity     | Part Number     | Description     |
1     | 1     | 174-7349     | Visor     |
2     | 1     | 174-7340     | Visor Kit     |
3     | 8     | 174-7335     | Bracket     |
4     | 8     | 174-7337     | Bracket     |
5     | 1     | 174-7348     | Visor     |
6     | 1     | 174-7346     | Visor     |
7     | 8     | 174-7336     | Ring     |
8     | 14     | 131-3987     | Screw     |
9     | 1     | 174-7338     | Visor Kit     |
10     | 1     | 174-7347     | Visor     |
11     | 1     | 174-7339     | Visor Kit     |
Illustration 1 | g00593342 |
159-3693 Cab Visor Kit (1) 174-7349 Visor (2) 174-7340 Visor Kit (3) 174-7335 Bracket (4) 174-7337 Bracket (5) 174-7348 Visor (6) 174-7346 Visor (7) 174-7336 Ring (8) 131-3987 Screw (9) 174-7338 Visor Kit (10) 174-7347 Visor (11) 174-7339 Visor Kit |
Left Window
Illustration 2 | g00587738 |
- Locate 174-7337 Bracket (4) on the gusset that is located on the top right hand side of the left window frame.
- Use 174-7337 Bracket (4) to mark the hole location. The location of the hole should be 25 mm (.98 inch) from the top of the gusset and 38 mm (1.50 inch) from the edge of the gusset.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the gusset. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Locate 174-7337 Bracket (4) on the gusset that is located on the bottom right hand side of the left window frame.
Illustration 3 | g00587769 |
- Use 174-7337 Bracket (4) to mark the hole location. The location of the hole should be 42 mm (1.65 inch) from the bottom of the gusset and 28 mm (1.10 inch) from the edge of the gusset.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the gusset. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Locate 174-7335 Bracket (3) on the left hand side of the left window frame.
Illustration 4 | g00587780 |
- Use 174-7335 Bracket (3) to mark the hole location. The location of the hole should be 68 mm (2.67 inch) from the top of the window frame and 20 mm (.79 inch) from the side of the window frame.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the left side of the left window frame. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Locate 174-7335 Bracket (3) on the bottom left hand side of the left window frame.
Illustration 5 | g00587787 |
- Use 174-7335 Bracket (3) to mark the hole location. The location of the hole should be 320 mm (12.60 inch) from the bottom left hand side of the window frame.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the bottom of the left window frame. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Place two 174-7336 Rings (7) onto 174-7347 Visor (10). Refer to Illustration 1.
Illustration 6 | g00608560 |
174-7347 Visor |
- Pull out 174-7347 Visor (10) in order to cover the window. Hook 174-7336 Rings (7) to 174-7335 Brackets .
- Use 174-7339 Visor Kit (11) in order to cover the remaining space on the window.
Right Window
Illustration 7 | g00588409 |
- Locate 174-7337 Bracket (4) onto the gusset that is located on the top left hand side of the right window frame.
- Use 174-7337 Bracket (4) to mark the hole location. The 174-7337 Bracket (4) should be against the top of the gusset. The location of the hole should be 38 mm (1.50 inch) from the edge of the gusset.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the gusset. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Locate 174-7337 Bracket (4) onto the left hand side of the right window frame.
Illustration 8 | g00588418 |
- Use 174-7337 Bracket (4) to mark the hole location. The location of the hole should be 75 mm (2.9 inch) from the top of the control panel.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the left hand side of the right window frame. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Install 174-7337 Bracket (4) to the left hand side of the right window frame with one 131-3987 Screw (8) .
- Locate 174-7335 Bracket (3) onto the right hand side of the right window frame.
Illustration 9 | g00588420 |
- Use 174-7335 Bracket (3) to mark the hole location. The location of the hole should be 107 mm (4.2 inch) from the top right hand side of the right window frame.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the right hand side of the right window frame. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Install 174-7335 Bracket (3) to the right hand side of the right window frame with one 131-3987 Screw (8) .
- Locate 174-7335 Bracket (3) on the bottom right hand side of the right window frame.
Illustration 10 | g00588422 |
- Use 174-7335 Bracket (3) to mark the hole location. The location of the hole should be 337 mm (13.3 inch) from the bottom right hand side of the right window frame.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the bottom of the right window frame. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Place two 174-7336 Rings (7) onto 174-7349 Visor (1). Refer to Illustration 1.
Illustration 11 | g00596014 |
174-7349 Visor |
- Use 174-7340 Visor Kit (2) to cover the remaining space on the window.
Rear Window
Illustration 12 | g00588691 |
- Locate 174-7337 Bracket (4) onto top inside part of the rear window frame.
- Use 174-7337 Bracket (4) to mark the hole location. The location of the hole should be 100 mm (3.9 inch) from the right hand side of the rear window frame.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the top inside part of the rear window frame. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Repeat the procedure for the opposite side of the window.
- Locate 174-7335 Bracket (3) onto the bottom right hand side of the rear window frame.
Illustration 13 | g00588744 |
- Use 174-7335 Bracket (3) to mark the hole location. The location of the hole should be 80 mm (3.1 inch) from the right hand side of the rear window frame.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the bottom of the rear window frame. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Repeat the procedure for the opposite side of the window.
- Place two 174-7336 Rings (7) onto 174-7348 Visor (5). Refer to Illustration 1.
Illustration 14 | g00596023 |
174-7348 Visor |
Front Window
- Locate 174-7337 Bracket (4) on the gusset that is located on the top left hand side of the front window frame.
Illustration 15 | g00593549 |
- Use 174-7337 Bracket (4) to mark the hole location. Mount 174-7337 Bracket (4) onto the gusset below the actuator on the door.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the gusset that is located on the top left hand side of the front window frame. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Locate 174-7337 Bracket (4) on the gusset that is located on the top right hand side of the front window frame.
Illustration 16 | g00593579 |
- Use 174-7337 Bracket (4) to mark the hole location.
- Drill and tap a hole for an M4 screw with 0.7 mm thread into the gusset that is located on the top right hand side of the front window frame. Use a 3.3 mm (.130 inch) drill bit to drill the hole.
- Install 174-7335 Bracket (3) to the bottom of the front window by using the existing screw in the front panel.
Illustration 17 | g00593587 |
- Repeat this procedure for the left side of the front window.
- Place two 174-7336 Rings (7) onto 174-7346 Visor (6). Refer to Illustration 1.
Illustration 18 | g00596038 |
174-7346 Visor |
- Use 174-7338 Visor Kit (9) to cover the remaining space on the window.