Crankshaft - Remove
拆卸步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件名称 | 数量 |
| A | 138-7575 | 连接支架 | 2 |
| B | 8B-7551 | 轴承拉拔器 | 1 |
| 8B-7549 | 拉拔器腿 | 2 | |
| 3H-0465 | 压拉器板 | 4 | |
| 1B-4207 | 全高螺母 | 2 | |
| 8B-7560 | 垫板 | 1 | |
| 1P-0820 | 液压拉拔器 | 1 | |
| 9U-6600 | 手动液压泵 | 1 | |
开始:
- 拆卸前壳体。 请参考解体与组装, "前壳体 - 拆卸"。
- 拆卸飞轮壳体。 请参考解体与组装, "飞轮壳体 - 拆卸和安装"。
- 拆卸发动机机油泵。 请参考解体与组装, "发动机机油泵 - 拆卸"。
- 拆下油底壳护板。 请参考解体与组装, "发动机油底壳护板 - 拆卸和安装"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 转动曲轴，直到曲轴齿轮 (1) 上的正时标记 "C" 与凸轮轴齿轮 (2) 上的正时标记 "C" 对准。
Show/hide table
 | |
| 图 1 | g00503163 |
- 从连杆上拆下连杆螺母 (4) 和连杆盖 (3) 。
Show/hide table
 | |
| 图 2 | g00503180 |
- 向下推动不处于上止点的活塞，以便使曲轴转到不碍事的地方。
Show/hide table
| 注意 |
|---|
如果将活塞和连杆推入到缸套中过深，则可能损坏燃油喷嘴或活塞。 |
注: 在进气门和排气门关闭的情况下，活塞难以向下推入到气缸中。
- 从缸体中拆下主轴承盖螺栓 (5) 和主轴承盖 (6) 。
- 从后主轴承上拆下止推板 (7) 。
Show/hide table
 | |
| 图 3 | g00503320 |
- 如图所示，在曲轴 (8) 上安装工具 (A) 和适当的举升设备。 将曲轴从缸体中垂直向上提升出来。 3304B 曲轴的重量为 65 kg (143 lb)。 3306B 曲轴的重量为 95 kg (210 lb)。
Show/hide table
 | |
| 图 4 | g00503353 |
- 使用工具 (B) 从曲轴上拆下曲轴齿轮和油封承磨衬套。
Show/hide table
 | |
| 图 5 | g00503384 |
- 分别从主轴承盖和缸体上拆下主轴承。 分别从连杆和连杆盖上拆下连杆轴承。
注: 拆卸前在轴承和轴承盖上作上识别标记。
Caterpillar Information System:
8-16B, 10-20B and 10-20WB Extend-A-Mat<COMP-BREAK TAGNAME=cp850>©<COMP-RESUME> Screed Feeder Control Sensor
3512B and 3516B Engines Engine Design
539 Knuckleboom Loader Hydraulic System Relief Valve (Delimber and Stabilizer Load Sensing) - Test and Adjust
797 Off-Highway Truck Fan Drive Hydraulic System Fan Drive Hydraulic System
CB-634C Vibratory Compactor Cooling System Coolant (DEAC) - Change
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Disassemble
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Rear) - Install
938G Wheel Loader and IT38G Integrated Toolcarrier Implement Restraint (Roading)
Installation Instructions for Mounting Cab Visors onto Cab Windows{7301} Installation Instructions for Mounting Cab Visors onto Cab Windows{7301}
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Engine Oil Filter Base
539 Knuckleboom Loader Hydraulic System Relief Valve (Line) - Test and Adjust
3304B and 3306B Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Assemble
3304B and 3306B Engines for Caterpillar Built Machines Piston Cooling Jets - Remove and Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Water Pump
Challenger 65C, Challenger 65D, Challenger 65E, Challenger 70C, Challenger 75C, Challenger 75D, Challenger 75E, Challenger 85C, Challenger 85D, Challenger 85E and Challenger 95E Agricultural Tractors Machine Performance Panel Testing and Adjusting
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
3304B and 3306B Engines for Caterpillar Built Machines Engine Oil Pump - Install
CB-534C and CB-634C Vibratory Compactors Vibratory System Drum (Split)
797 Off-Highway Truck Engine Coupling Oil Filter - Replace
TH62, TH63, TH82 and TH83 Telehandlers Starting with Jump Start Cables
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Belt Tensioner
797 Off-Highway Truck Fan Drive Hydraulic System Piston Pump (Fan Drive) Pressure - Test and Adjust
D350E Series II Articulated Truck Power Train Differential and Bevel Gear (Center) - Remove