Troubleshooting Diagnostic Codes
Show/hide table
Diagnostic Codes that are Detected by the Transmission Electronic Control Module     | |
---|---|
CID and FMI     | Description     |
CID 168     | Electrical System     |
FMI 00     | Data valid but above normal operational range     |
FMI 01     | Data valid but below normal operational range     |
CID 191     | Speed Sensor (Transmission Output)     |
FMI 08     | Abnormal frequency, pulse width, or period     |
CID 520     | The configuration of the transmission     |
FMI 02     | Data erratic, intermittent, or incorrect     |
CID 641     | Solenoid Valve (Forward High)     |
FMI 03     | Voltage above normal or shorted high     |
FMI 05     | Current below normal or open circuit     |
FMI 06     | Current above normal or grounded circuit     |
CID 642     | Solenoid Valve (Reverse)     |
FMI 03     | Voltage above normal or shorted high     |
FMI 05     | Current below normal or open circuit     |
FMI 06     | Current above normal or grounded circuit     |
CID 643     | Solenoid Valve (Forward Low)     |
FMI 03     | Voltage above normal or shorted high     |
FMI 05     | Current below normal or open circuit     |
FMI 06     | Current above normal or grounded circuit     |
CID 644     | Solenoid Valve (First and Second Gear)     |
FMI 03     | Voltage above normal or shorted high     |
FMI 05     | Current below normal or open circuit     |
FMI 06     | Current above normal or grounded circuit     |
CID 645     | Solenoid Valve (Third Gear)     |
FMI 03     | Voltage above normal or shorted high     |
FMI 05     | Current below normal or open circuit     |
FMI 06     | Current above normal or grounded circuit     |
CID 646     | Solenoid Valve (Fourth Gear)     |
FMI 03     | Voltage above normal or shorted high     |
FMI 05     | Current below normal or open circuit     |
FMI 06     | Current above normal or grounded circuit     |
CID 650     | The Plug for the Harness Code     |
FMI 02     | Data erratic, intermittent, or incorrect     |
CID 668     | Transmission Control (Shift Lever)     |
FMI 02     | Data erratic, intermittent, or incorrect     |
FMI 09     | Abnormal update     |
CID 683     | Relay (Parking Brake)     |
FMI 03     | Voltage above normal or shorted high     |
FMI 05     | Current below normal or open circuit     |
FMI 06     | Current above normal or grounded circuit     |
Caterpillar Information System:
416C, 426C, 428C, 436C and 438C Backhoe Loaders Transmission Electronic Control System CID 0683 FMI 06 Relay (Parking Brake) Current Above Normal - Test
3524B Engine for Caterpillar Built Machines Gear Group (Rear) - Remove
CB-534C and CB-634C Vibratory Compactors Vibratory System Drum (Split)
345B Excavator Bucket Tips - Inspect/Replace
CB-634C Vibratory Compactor Circuit Breakers - Reset
416C, 426C, 428C, 436C and 438C Backhoe Loaders Transmission Electronic Control System CID 0683 FMI 05 Relay (Parking Brake) Current Below Normal - Test
539 Knuckleboom Loader Hydraulic System Relief Valve (Main, Load Sensing) - Test and Adjust
Reconditioning of Bearing Surfaces and Pivot Shaft Ends {4153} Reconditioning of Bearing Surfaces and Pivot Shaft Ends {4153}
797 Off-Highway Truck Filter and Screen Locations
416C, 426C, 428C, 436C and 438C Backhoe Loaders Transmission Electronic Control System CID 0683 FMI 03 Relay (Parking Brake) Voltage Above Normal - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel Injection Lines - Remove and Install
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Exhaust Elbow
365B Excavator Cab Air Filter (Fresh Air) - Clean/Replace
3524B Engine for Caterpillar Built Machines Gear Group (Rear) - Install
789C Off-Highway Truck Power Train Tire and Rim (Rear) - Install
3304B and 3306B Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
539 Knuckleboom Loader Hydraulic System Relief Valve (Line) - Test and Adjust
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Engine Oil Filter Base
Installation Instructions for Mounting Cab Visors onto Cab Windows{7301} Installation Instructions for Mounting Cab Visors onto Cab Windows{7301}
938G Wheel Loader and IT38G Integrated Toolcarrier Implement Restraint (Roading)
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Rear) - Install
3524B Engine for Caterpillar Built Machines Accessory Drive (Front) - Disassemble
CB-634C Vibratory Compactor Cooling System Coolant (DEAC) - Change
797 Off-Highway Truck Fan Drive Hydraulic System Fan Drive Hydraulic System