Turbocharger - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 5P-3931     | 防粘结剂     | -     |
- 检查所有 O 形密封圈和部件有无磨损或损坏。 如有必要,请更换部件。
- 利用所密封的润滑剂轻轻润滑所有 O 形密封圈。
- 将 O 形密封圈 (17) 安装到管组件上。 将新密封垫 (16) 定位到排气歧管上。
Show/hide table
图 1 | g00871029 |
- 将适当起吊设备连在涡轮增压器 (13) 上。 涡轮增压器 (13) 的重量约为 35 kg (75 lb)。
Show/hide table
图 2 | g00870970 |
- 将涡轮增压器 (13) 定位到排气歧管 (15) 上。
- 将工具 (A) 涂抹到螺栓 (16) 的螺纹上。
注: 安装中使用新螺栓 (16) 。
- 将螺栓 (14) 安装到涡轮增压器 (13) 上。 用手带紧螺栓 (14) 。
注: 安装中使用新螺栓 (14) 。
- 将管组件定位到涡轮增压器上。 拧紧卡箍 (9) 和 (10) 。
Show/hide table
图 3 | g00870872 |
- 将管组件 (12) 连接到涡轮增压器上。 拧紧卡箍 (11) 。
Show/hide table
图 4 | g00871004 |
- 将 O 形密封圈安装到管组件 (8) 上。 将螺栓 (6) 安装到管组件 (8) 上。 安装支架 (7) 。
Show/hide table
图 5 | g00870645 |
- 将卡箍 (5) 定位到涡轮增压器和管组件 (2) 上。 将卡箍 (5) 上紧到 14 ± 3 N·m (124 ± 27 lb in) 的扭矩。
Show/hide table
图 6 | g00870627 |
- 将螺栓 (4) 安装到管组件 (3) 上。
- 将螺栓 (1) 安装到排气管组件 (2) 上。
Show/hide table
图 7 | g00870619 |
- 将用来将涡轮增压器 (13) 固定到排气歧管上的锁紧螺母上紧到 55 ± 5 N·m (41 ± 4 lb ft) 的扭矩。
- 关闭前后发动机罩。
End By: 拆下车斗固定销。 请参阅 拆解和组装, "挡圈和销钉(车斗)- 拆卸和安装"。
Caterpillar Information System:
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
769D Off-Highway Truck/Tractor and 771D Quarry Truck Power Train Final Drive
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove
527 Track-Type Skidder Alternator and Fan Belts - Inspect/Adjust/Replace
3406C Engines for Caterpillar Built Machines Cylinder Block Cover Group - If Equipped
IT14G Integrated Toolcarrier and 914G Wheel Loader Standard Power Train Piston Motor (Hydrostatic)
527 Track-Type Skidder Power Train Platform
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Motor Mounting (Hydrostatic)
D250E Series II and D300E Series II Articulated Trucks Machine Systems Steering Cylinder - Install
784C and 785C Off-Highway Trucks Machine Systems Control Valve (Hoist) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector - Install
988F and 988F Series II Wheel Loaders Power Train Transmission Hydraulic Control Valve - Assemble
3304B and 3306B Engines for Caterpillar Built Machines Housing (Front) - Remove
773E Off-Highway Truck Power Train Final Drive
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector Sleeve - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Universal Joint (Rear) - Remove and Install
554 Forwarder and 574 Forwarder Window Wiper and Washer Control
793C Off-Highway Truck/Tractor Power Train Differential and Bevel Gear - Install
527 Track-Type Skidder Battery - Inspect
3406C Engines for Caterpillar Built Machines Crankshaft Pulley
784C and 785C Off-Highway Trucks Machine Systems Control Valve (Hoist) - Install
3304B and 3306B Engines for Caterpillar Built Machines Housing (Front) - Install
CB-434C, CB-534C and CB-634C Vibratory Compactors Water Spray System Spray Nozzle
3406E On-Highway Engine Compression Brake - Remove - If Equipped