Steering Cylinder - Install
- Inspect all parts and clean all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Show/hide table
Illustration 1 g00511871 - Install O-ring seals (17) to the top and bottom of each end of cylinder (5).
Show/hide table
Illustration 2 g00511856 - Install shields (16) to the top and bottom of each end of cylinder (5).
Show/hide table
Illustration 3 g00511685 - Use the hoist in order to install the steering cylinder to the machine. The weight of the steering cylinder is
38 kg (84 lb) . Install hose clamp (12) to hydraulic hose (2) and cylinder (5).Show/hide tableIllustration 4 g00511651 - Lower the temperature of pin (13). Install bolt (15), washer (14) and pin (13) in order to secure the steering cylinder to the mounting bracket.
Show/hide table
Illustration 5 g00511646 - Lower the temperature of pin (8). Install pin (8), bolt (10) and washer (9) in order to secure the steering cylinder to the mounting bracket.
- Remove the nylon lifting strap and the hoist from the steering cylinder.
- Position grease line (7) to pin (8). Tighten nut (6) in order to connect grease line (7) to pin (8).
Show/hide table
Illustration 6 g00511645 - Tighten nut (4) in order to connect hydraulic hose (2) to cylinder (5). Tighten nut (3) in order to connect hydraulic hose (1) to cylinder (5).
- Install the steering cylinder to the other side of the machine by following Steps 1 through 9.
Caterpillar Information System:
784C and 785C Off-Highway Trucks Machine Systems Control Valve (Hoist) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector - Install
988F and 988F Series II Wheel Loaders Power Train Transmission Hydraulic Control Valve - Assemble
793C Off-Highway Truck/Tractor Power Train Differential and Bevel Gear - Remove
3304B and 3306B Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove
793C Off-Highway Truck/Tractor Power Train Flow Control and Relief Valve (Rear Axle Oil) - Assemble
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Standard Power Train Motor Mounting (Hydrostatic)
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Hydrostatic Drive
3406C Engines for Caterpillar Built Machines Belt Tensioner - Belt Tensioner Without Spring Tensioner
3176C and 3196 Engines For Caterpillar Built Machines Fuel Transfer Pump - Install
3176C and 3196 Engines For Caterpillar Built Machines Fuel Transfer Pump - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Motor Mounting (Hydrostatic)
527 Track-Type Skidder Power Train Platform
IT14G Integrated Toolcarrier and 914G Wheel Loader Standard Power Train Piston Motor (Hydrostatic)
3406C Engines for Caterpillar Built Machines Cylinder Block Cover Group - If Equipped
527 Track-Type Skidder Alternator and Fan Belts - Inspect/Adjust/Replace
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove
769D Off-Highway Truck/Tractor and 771D Quarry Truck Power Train Final Drive
3176C and 3196 Engines For Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Turbocharger - Install
3304B and 3306B Engines for Caterpillar Built Machines Housing (Front) - Remove
773E Off-Highway Truck Power Train Final Drive
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector Sleeve - Install