Engine Oil Pressure Sensor - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| |
| Illustration 1 | g01064064 |
Show/hide table
| |
| Illustration 2 | g01023042 |
- Disconnect the harness assembly from engine oil pressure sensor (1). Cut the cable straps that secure the harness assembly to the engine.
- Remove engine oil pressure sensor (1).
- Inspect the condition of the O-ring seal on engine oil pressure sensor (1). Replace the O-ring seal, if necessary.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
|
| |
| Illustration 3 | g01023042 |
Show/hide table
|
| |
| Illustration 4 | g01064064 |
- Install engine oil pressure sensor (1). Tighten the engine oil pressure sensor to a torque of
10 ± 2 N·m (89 ± 18 lb in) . - Connect the harness assembly to engine oil pressure sensor (1). Secure the harness assembly to the engine with cable straps.
Caterpillar Information System:
769D Off-Highway Truck/Tractor and 771D Quarry Truck Power Train Final Drive
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove
527 Track-Type Skidder Alternator and Fan Belts - Inspect/Adjust/Replace
3406C Engines for Caterpillar Built Machines Cylinder Block Cover Group - If Equipped
IT14G Integrated Toolcarrier and 914G Wheel Loader Standard Power Train Piston Motor (Hydrostatic)
527 Track-Type Skidder Power Train Platform
IT14G Integrated Toolcarrier and 914G Wheel Loader Power Train Motor Mounting (Hydrostatic)
D250E Series II and D300E Series II Articulated Trucks Machine Systems Steering Cylinder - Install
784C and 785C Off-Highway Trucks Machine Systems Control Valve (Hoist) - Remove
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector - Install
988F and 988F Series II Wheel Loaders Power Train Transmission Hydraulic Control Valve - Assemble
793C Off-Highway Truck/Tractor Power Train Differential and Bevel Gear - Remove
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Turbocharger - Install
3304B and 3306B Engines for Caterpillar Built Machines Housing (Front) - Remove
773E Off-Highway Truck Power Train Final Drive
3176C and 3196 Engines For Caterpillar Built Machines Electronic Unit Injector Sleeve - Install
D250E Series II and D300E Series II Articulated Trucks Power Train Universal Joint (Rear) - Remove and Install
554 Forwarder and 574 Forwarder Window Wiper and Washer Control
793C Off-Highway Truck/Tractor Power Train Differential and Bevel Gear - Install
527 Track-Type Skidder Battery - Inspect
3406C Engines for Caterpillar Built Machines Crankshaft Pulley
784C and 785C Off-Highway Trucks Machine Systems Control Valve (Hoist) - Install
3304B and 3306B Engines for Caterpillar Built Machines Housing (Front) - Install
CB-434C, CB-534C and CB-634C Vibratory Compactors Water Spray System Spray Nozzle