Governor Identification - Introduction
This service manual contains instructions for servicing the 3114, 3116, and 3126 Engine Governors on the 1U-7326 Governor Calibration Bench. The final low idle speed may be adjusted with the governor on the engine. All other adjustments must be performed on this calibration bench.
Show/hide table
Illustration 1 | g00518799 |
Typical governor information plate |
Governor information plate (1) is located on top of the governor. The information plate provides the following information:
- Serial Number and Type Code
- Group Part Number
- Production Codes
The information on governor information plate (1) and the physical appearance of the governor is used to identify the governor. The type code follows the serial number. There are seven different types of governors for the 3114, 3116, and 3126 Engines. The following information will aid in the proper identification of each of the seven types of governors.
Show/hide table
Governor Identification Chart     | |||
Governor Type     | Type Code     | Throttle Lever     | Components     |
Type I     | "A"     | Type I     |     |
Type II     | "B"     | Type I     | No Servo, 4 Flyweight's     |
Type III     | "C"     | Type I or II     |     |
Type IV     | "A", "0", "1"     | Type II     |     |
Type V     | "D"     | Type II     | Cast FRC Housing     |
Type VI (1)     | "D"     | Type II     | Dual Horsepower     |
Type VII (1)     | "D"     | Type II     | Dual Horsepower     |
Show/hide table
( 1 ) | Both Type VI and Type VII Governors are variations of the Type V Governor. |
Caterpillar Information System:
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Brake Valve (Parking and Secondary) - Install
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Tilt Cylinder - Isolation and Drift Check
554 Forwarder and 574 Forwarder Hydraulic System Pressure Reducing Valve (Maximum Signal)
IT14G Integrated Toolcarrier and 914G Wheel Loader Standard Power Train Creeper Control - If Equipped
784C, 785C and 785C HAA Off-Highway Truck Air System and Brakes Gear Pump (Hoist and Rear Brake Cooling)
554 Forwarder and 574 Forwarder Hydraulic System Diverter Valve (Boom Tilt Cylinder and Gate Cylinder)
143H and 163H Motor Graders All Wheel Drive Solenoid Valve (Charge) - Test
789C Off-Highway Truck/Tractor Air System and Brakes Gear Pump (Torque Converter, Parking Brake Release, and Brake Cooling)
773D, 773E, 775D and 775E Off-Highway Trucks Machine Systems Brake Valve (Parking and Secondary) - Remove
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Loader Frame and Rear Frame - Connect
789C Off-Highway Truck/Tractor Air System and Brakes Hydraulic Tank (Torque Converter, Hoist, Brake, and Transmission)
3408E and 3412E Engines for Caterpillar Built Machines Fuel Filter Base
784C and 785C Off-Highway Trucks Machine Systems Steering Cylinder - Remove
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Check Valve (Air/Hydraulic Cylinder) - Remove and Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Machine Systems Check Valve (Primary Air Tank) - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Steering Cylinder - Install
IT14G Integrated Toolcarrier and 914G Wheel Loader Standard Power Train Hydrostatic System
G3B, K3A and L3A Denso Alternators T3 Charging System - Test
3304B and 3306B Engines for Caterpillar Built Machines Crankshaft - Install
143H and 163H Motor Graders All Wheel Drive Solenoid Valve (All Wheel Drive) - Test
3114, 3116 and 3126 MUI Engine Governors Governor (Type I)
583R Pipelayer Power Train Steering Clutch and Brake - Assemble
69D, 769D , 773D, 773E, 776D, 777D, 784C, 785C, 785D, 789C, 789D, 793C and 793D Off-Highway Trucks and 771D, 775D and 775E Quarry Trucks Braking System General Information
3114, 3116 and 3126 MUI Engine Governors Governor (Type II)