Drive Shaft (Center) - Remove and Install
Removal Procedure
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
- Park the machine on a flat, level surface. Lower the bucket to the ground. Chock the wheels in order to keep the machine from rolling when the drive shaft is removed.
- Support center drive shaft (2). Remove four bolts (1) and two straps (3) from each end of center drive shaft (2) .
Show/hide table
Illustration 1 | g00291797 |
- Carefully remove center drive shaft (2) .
Installation Procedure
Show/hide table
NOTICE |
---|
When the center drive shaft is installed, it must be installed in phase with the front and rear drive shafts. Serious component damage could occur. Be certain that all the joint group, all the yokes, and all the lubricating fittings are aligned. |
- Carefully install center drive shaft (2) .
Show/hide table
Illustration 2 | g00291797 |
- Support center drive shaft (2). Install two straps (3) and four bolts (1) on each end of center drive shaft (2). The torque for bolts (1) is 60 ± 10 N·m (44 ± 7 lb ft).
- Lubricate the center drive shaft. Refer to Operation and Maintenance Manual, SEBU7018, "950G Wheel Loader and 962G Wheel Loader" for the correct procedure.
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
561M Pipelayer Equalizer Bar
561M Pipelayer Pivot Shaft
3208 Marine Engine Cooling System Coolant (DEAC) - Change
IT14G Integrated Toolcarrier Fuel Injection Timing - Check
3126B Engines Cooling System
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Parking Brake
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train Drive Shaft (Front) - Remove and Install
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Brake Accumulator
966G Wheel Loader and 972G Wheel Loader Steering System Relay (Secondary Steering Motor)
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Lift Kickout
824G Wheel Tractor, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System Pump Flow - Test
784C, 785C and 785C HAA Off-Highway Truck/Tractors Steering System Front Wheel
966G Wheel Loader and 972G Wheel Loader Hydraulic System Hood Tilt Actuator
3208 Marine Engine Cooling System Coolant (ELC) - Change
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train Pinout Specifications for Electronic Control (Power Train)
789C Off-Highway Truck Air System and Brakes Front Wheel
793B Off-Highway Truck Model View Illustrations
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Brake Control Valve (Parking)
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train Drive Shaft (Rear) - Remove and Install
IT62G Series II Integrated Toolcarrier Tilt Cylinder Bearings and Bucket Linkage Bearings - Lubricate
C15 and C18 Petroleum Generator Sets Fan Drive Bearing - Lubricate
966G Wheel Loader and 972G Wheel Loader Hydraulic System Oil Filter (Hydraulic)
3408E and 3412E Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve
793C and 793C XQ Off-Highway Truck Air System and Brakes Air Control Valve (Window Wiper)