Drive Shaft (Rear) - Remove and Install
Removal Procedure
Start By:
- Remove the power train guard. Refer to Disassembly and Assembly, "Power Train Guard (Transmission) - Remove and Install".
- Park the machine on a flat, level surface. Lower the bucket to the ground. Chock the wheels in order to prevent the machine from rolling when the drive shaft is removed.
- Support rear drive shaft (2). Remove four bolts (3) and two straps (4) from each end of rear drive shaft (2) .
Show/hide table
Illustration 1 | g00296320 |
- Slide yoke (1) toward the rear axle assembly. Slide yoke (1) so that enough clearance is provided for the removal of rear drive shaft (2) .
- Carefully remove rear drive shaft (2) .
Installation Procedure
Show/hide table
NOTICE |
---|
When the rear drive shaft is installed, it must be installed in phase with the rear axle assembly yoke. The rear drive shaft must be installed in phase with the center and front drive shafts. Serious component damage could occur. Be certain that all the joint groups, all the yokes, and all the lubricating fittings are aligned. |
- Slide yoke (1) toward the rear axle assembly so that enough clearance is provided for the installation of rear drive shaft (2) .
Show/hide table
Illustration 2 | g00296320 |
- Carefully install rear drive shaft (2) .
- Slide yoke (1) toward the rear drive shaft so that rear drive shaft (4) is properly located.
- Support rear drive shaft (2). Install two straps (4) and four bolts (3) on each end of rear drive shaft (2). The torque for bolts (3) is 60 ± 10 N·m (44 ± 7 lb ft).
- Lubricate the rear drive shaft. Refer to Operation and Maintenance Manual, SEBU7018, "950G Wheel Loader and 962G Wheel Loader" for the correct procedure.
End By: Install the power train guard. Refer to Disassembly and Assembly, "Power Train Guard (Transmission) - Remove and Install".
Caterpillar Information System:
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Brake Control Valve (Parking)
793B Off-Highway Truck Model View Illustrations
789C Off-Highway Truck Air System and Brakes Front Wheel
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train Pinout Specifications for Electronic Control (Power Train)
3208 Marine Engine Cooling System Coolant (ELC) - Change
966G Wheel Loader and 972G Wheel Loader Hydraulic System Hood Tilt Actuator
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train Drive Shaft (Center) - Remove and Install
561M Pipelayer Equalizer Bar
561M Pipelayer Pivot Shaft
3208 Marine Engine Cooling System Coolant (DEAC) - Change
IT14G Integrated Toolcarrier Fuel Injection Timing - Check
3126B Engines Cooling System
IT62G Series II Integrated Toolcarrier Tilt Cylinder Bearings and Bucket Linkage Bearings - Lubricate
C15 and C18 Petroleum Generator Sets Fan Drive Bearing - Lubricate
966G Wheel Loader and 972G Wheel Loader Hydraulic System Oil Filter (Hydraulic)
3408E and 3412E Engines for Caterpillar Built Machines Injection Actuation Pressure Control Valve
793C and 793C XQ Off-Highway Truck Air System and Brakes Air Control Valve (Window Wiper)
789B Off-Highway Truck Air System and Brakes Service and Parking Brake (Front)
3126B Engine for Caterpillar Built Machines Valve Rocker Arms, Lifters, and Bridges
784C and 785C Off-Highway Truck/Tractors Air System and Brakes Slack Adjuster (Rear)
3126B Engine for Caterpillar Built Machines Cylinder Head Valves
416C, 426C, 428C, 436C and 438C Backhoe Loaders Hydraulic Lock Control - If Equipped
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Braking System Vane Pump (Implement, Pilot and Braking)
416C, 426C, 428C, 436C and 438C Backhoe Loaders Brake Reservoir Oil Level - Check