Lift Kickout
Show/hide table
 |
调整附件提升限位时，要小心避免造成人身伤害。 其他人员应远离机器。 在附件连杆下面或周围工作时，清除区域障碍。 附件提升后，附件和/或连杆必须有可靠的支撑。 |
- 起动发动机。 将铲斗或附件升至理想提升限位高度并关闭发动机。
- 松开螺母 (4) 。 调整控制总成 (1) ，使磁铁 (3) 的下缘与控制总成 (1) 的中心平齐。
Show/hide table
 | |
| 图 1 | g00297678 |
950G 和 962G | |
Show/hide table
 | |
| 图 2 | g00495490 |
IT62G 和 962G 平行提升机器 | |
- 拧紧螺母 (4) 。
- 松开螺栓 (2) 。 调整控制总成 (1) ，使端面与磁铁 (3) 相距 8 ± 2 mm (0.32 ± 0.08 in)。
- 拧紧螺栓 (2) 。
- 为检查调整，起动发动机。 将提升操纵杆移到提升止动位置。
铲斗或附件达到预设高度时，提升操纵杆应返回保持位置。
- 如果限位位置不正确，再次执行步骤 1 至 6。
Caterpillar Information System:
824G Wheel Tractor, 825G Soil Compactor and 826G Landfill Compactor Hydraulic System Pump Flow - Test
784C, 785C and 785C HAA Off-Highway Truck/Tractors Steering System Front Wheel
789B Off-Highway Truck Air System and Brakes Diverter Valve (Hoist)
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Hydraulic System Relief Valve (Line)
IT14G Integrated Toolcarrier Warranty Information
IT14G Integrated Toolcarrier Cooling System Coolant (ELC) - Change
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train Crankcase Guard - Remove and Install
IT14G Integrated Toolcarrier Cooling System Coolant Extender (ELC) - Add
3126B Engine for Caterpillar Built Machines Crankshaft Seals
980G Wheel Loader Hydraulic System Hydraulic System Troubleshooting
IT14G Integrated Toolcarrier Engine Valve Lash - Check
793B Off-Highway Truck Air System and Brakes Air Starting Motor
966G Wheel Loader and 972G Wheel Loader Steering System Relay (Secondary Steering Motor)
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Brake Accumulator
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train Drive Shaft (Front) - Remove and Install
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Parking Brake
3126B Engines Cooling System
IT14G Integrated Toolcarrier Fuel Injection Timing - Check
3208 Marine Engine Cooling System Coolant (DEAC) - Change
561M Pipelayer Pivot Shaft
561M Pipelayer Equalizer Bar
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Power Train Drive Shaft (Center) - Remove and Install
966G Wheel Loader and 972G Wheel Loader Hydraulic System Hood Tilt Actuator
3208 Marine Engine Cooling System Coolant (ELC) - Change