1997/12/22 Caterpillar


New Seat Slider Blocks Reduce Need For Adjustments {7312,7300}

Usage:


All Caterpillar Machines Using The Contour Series Seat

Reference: Service Manual Module, SENR6615-01, Contour Series Seat Installation and Repair, Page 12.

Description of Change: New fore and aft slider blocks have a flat surface instead of a rounded surface. This flat surface will not wear significantly and eliminates the need for adjustment because of the rounded surface wearing flat.

Adaptable To: The 149-4745 Slider Block Kit replaces the former 8Y-5889 Slider Block Kit, and is adaptable to earlier machines by replacing the existing slider blocks with the 149-4744 Slider Blocks from the 149-4745 Slider Block Kit.

NOTE: The 149-4744 Slider Blocks are not serviced individually, but are available in the 149-4745 Slider Block Kit.

NOTE: Earlier machines using the former slider blocks can be adjusted without replacing the slider blocks by following the procedure in the Service Manual referenced above. This adjustment is recommended after 250 wear in hours and as required thereafter.

Caterpillar Information System:

1997/12/22 Dry Lubricant Recommended For Use On Door Linkages, Door Seals, And Window Latches {7308}
1997/12/22 Cylinder Sleeve Available For Reconditioning Cylinder Blocks {1222}
1997/12/22 Thicker Head Gasket Available For Cylinder Block Salvage Procedure {1124}
1997/12/22 New Tightening Specification For "Spin-on" Oil Filter Assembly {1306,1308}
1997/12/22 Removing Trapped Air In Hydraulic Lines And Auxiliary Attachments In Order To Prevent Drift {5057,5116,6408}
1997/12/22 Eye End (Brake Cable) Attachment Pin And Related Hardware Available {4267}
1997/12/22 New Hydrostatic Drive Pump Group Has Stronger Head {3203}
1997/12/22 Revised Systems Operation Testing And Adjusting Manual, SENR5890-02, Transmission Electronic Control System, Now Available {0375,3168}
1997/12/22 New Screen Covers For Hoods And Side Panel Louvers Now Available To Prevent Debris And Snow Ingress {7315,1151}
1997/12/22 New Autoshift Transmission Available {3030,3168,7459}
1997/12/22 Brake Purge Ports Added To Improve Brake Serviceability {4251}
1997/12/22 Recommended Tire And Rim Usage {4201,4202,4203}
1997/12/22 The 3P-8993 Speaker Assembly Discontinued And Replaced By 123-6449 Back-Up Alarm {7406}
1998/01/05 Components Available To Strengthen Engine Air Inlet System {1055,1071}
1998/01/05 Guard Assembly Available To Protect Rear Axle Filtration System And Lube Lines {3004,7150}
1998/01/05 Jacobs Engine Brake Parts Service Now Available {1129}
1998/01/05 New VIMS Service Manual Is Available {7601}
1998/01/05 VIMS-PC Version 2.4 Upgrade {7601}
1998/01/05 New VIMS Message Center Display Available {7601}
1998/01/05 New Water Separator Available {1250,1263}
1998/01/05 Correct Boom Chain Information {6404,6460}
1998/01/05 Service Kits Available For Telehandler Roof Wiper {7305}
1998/01/19 Use 125-4633 Plate To Remove And Install Transmission{0635,3030,3150}
1998/01/19 Lubrication Intervals When Using Hammers On Backhoe Loaders{6333}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.