Points To Remember When Replacing A Viscous Crankshaft Damper Assembly With A Rubber Crankshaft Damper Assembly {1205}
Usage:
Caterpillar Machines Powered By 3406, 3406B And 3406C Engines
- SUPPLEMENT: 03/03/97
Service Magazine; January 27, 1997; Page 35;"Points To Remember When Replacing A Viscous Crankshaft Damper Assembly With A Rubber Crankshaft Damper Assembly"
The title of the article is NOT correct. The correct title follows:
Points To Remember When Replacing A Rubber Crankshaft Damper Assembly With A Viscous Crankshaft Damper Assembly
--------------- END SUPPLEMENT ---------------
Reference: Service Magazine; August 21, 1995; Page 9: "Recommendations For Inspection And Replacement Of Rubber and Viscous Crankshaft Dampers".
When replacing a rubber crankshaft damper assembly with a 7E-9520 Viscous Crankshaft Damper Assembly:
-
- * The viscous damper must have a 9Y-8870 Plate installed on the outside of the viscous damper.
- * The washers must be removed from the bolts that fasten the damper to the crankshaft so the bolts will have the proper thread engagement.
- * The viscous damper must have a 9Y-8870 Plate installed on the outside of the viscous damper.
Caterpillar Information System:
1997/01/27 Premachined Valve Seat Inserts And Precision Valve Guide Increase Valve Life {1103,1104}
1997/01/27 Field Repair Of Single Wire Breaks In Harnesses {1408}
1997/01/27 Use Of Windows Write (Or Notepad) And Paintbrush For Taking Field Notes {0785,7601}
1997/01/27 VIMS Exhaust Temperature Sensor Is Improved {7601,1919}
1997/01/27 New Replacement Procedure For Hydraulic Hoses Inside The Telescopic Material Handler Boom {5057,6460}
1997/01/27 C-V (U) Joint Life Extended Through Correct Operation Of The Differential Lock {3274,2453,3259,3260,3264}
1997/01/27 Repair Centers For Sonic Grade Sensors Established {5645}
1997/01/27 New Control Lever Group Requires Spacer {1265,3209,5258}
1997/01/27 Hydraulic Hose Retention For Vibratory And Drum Propel Systems Improved {5057}
1997/01/27 Verify Offset Dimension When Ordering New Wheel Assembly {4209,4202}
1997/01/27 New Brake Bleeding Procedure {4250,4293}
1997/01/27 Solution To Cab Window Fogging {1818,7309,7310,7320}
1997/01/27 Checking The Alignment Of Timing Gear Marks {1206}
1997/01/27 Engine Oil Recommendation For 3408E (99C) And 3412E (80M) Engines {1318}
1997/01/27 125-0200 Camshaft Pilot To Remove And Install 106-4584 Camshaft {1202}
1997/01/27 128-3102 Tap Assembly And 128-3104 Stud Puller To Remove Injector Sleeves With Oversized Lower Bore {1125}
1997/01/27 Cylinder Head Stress Plate Used During Cylinder Bore Honing And Measurement {1223}
1997/01/27 127-1069 Timing Pin Used To Set Piston At 100° BTDC When Testing And Adjusting Fuel Systems {1250}
1997/01/27 127-5090 Coupling Socket For Removing And Installing The Implement Hydraulic Coupling Sleeve {5051,5051}
1997/01/27 Service Tools For Disassembly And Assembly Of All Wheel Steer Rear Axle {3254,3258,3260,4084,4321}
1997/01/27 131-3961 Tool Group For Reclaiming Tooling From XT Hose Assemblies {5057}
1997/01/27 130-6061 Hose Cleaner Group For Cleaning Insides Of Hydraulic Tubes, Lines And Hoses {5057,0738}
1997/01/27 FT2511 Shaft Alignment Tool Simplifies Assembly Of Eccentric Weight {6606}
1997/02/03 9U-5665 Test Stand Group For Testing Steering Control Units {4100,4100}