Flywheel Housing - Remove and Install
Reference: Special Instruction, "Visual Service Procedures - Colors and Symbols" M0066576.
Start By:
- Remove the flywheel.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.
Show/hide table
Illustration 1 | g06263626 |
Show/hide table
Illustration 2 | g06263627 |
Show/hide table
Illustration 3 | g06263630 |
Note: Turn the sea water feed to the off position.
Show/hide table
Illustration 4 | g06263633 |
Show/hide table
Illustration 5 | g06263634 |
Show/hide table
Illustration 6 | g06263639 |
Show/hide table
Illustration 7 | g06263641 |
Show/hide table
Illustration 8 | g06263642 |
If necessary, remove the dowels. |
- Install the flywheel housing in the reverse order of removal.
Show/hide table
Illustration 9 | g06263643 |
Tightening sequence for the bolts. |
Show/hide table
Illustration 10 | g06263645 |
Show/hide table
Illustration 11 | g06263646 |
Show/hide table
Illustration 12 | g06263650 |
Caterpillar Information System:
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Parking
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Mounting and Dismounting
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Alternate Exit
New Engine Software Are Now Used for Certain C27 and C32 Engines {1920} New Engine Software Are Now Used for Certain C27 and C32 Engines {1920}
New Injector Jumper Harness is Now Available for Certain 3406E Truck Engines {1120, 1403} New Injector Jumper Harness is Now Available for Certain 3406E Truck Engines {1120, 1403}
Update on Plastic Plugs for Certain Cat® C13 and C15 Defra Base Generator Sets {1273} Update on Plastic Plugs for Certain Cat® C13 and C15 Defra Base Generator Sets {1273}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Seat
New Injector Hold Down Clamps Are Used for Certain C175 Locomotive Engines {1251, 1290} New Injector Hold Down Clamps Are Used for Certain C175 Locomotive Engines {1251, 1290}
New Instruction for Tightening Fuel Cooler Hose is Now Available for Certain C15 and C18 Engines {1353, 1712} New Instruction for Tightening Fuel Cooler Hose is Now Available for Certain C15 and C18 Engines {1353, 1712}
New Engine Software is Now Used for Certain C175 Locomotive Engines {1920} New Engine Software is Now Used for Certain C175 Locomotive Engines {1920}
XQP1100 Generator Set Generator Operation
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Pump Control
C9.3B Engines Manifold (Diesel Exhaust Fluid)
3516C Petroleum Engine Fuel System - Prime
C32 XQP1100 Generator Sets Diagnostic Trouble Codes
G3516 Petroleum Engines Aftercooler - Disassemble
G3516 Petroleum Engines Aftercooler - Assemble
C7.1 Marine Propulsion Engine Valve Mechanism Cover - Remove and Install
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Rear Steering) - Disassemble
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Rear Steering) - Assemble
C9.3B Engines Cylinder Liner
C7.1 Marine Propulsion Engine Coolant Level Sensor - Remove and Install
C7.1 Marine Propulsion Engine Coolant Temperature Sensor - Remove and Install
C7.1 Marine Propulsion Engine Engine Oil Pressure Sensor - Remove and Install