Aftercooler - Disassemble
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 477-3194 | Eyebolt AS | 2 |
Start By:
- Remove the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Inspect all O-rings, seals, and gaskets for wear and damage. Replace if necessary. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Attach Tooling (A) and a suitable lifting device to aftercooler housing (2). The weight of aftercooler housing (2) is approximately
22 kg (48.5lb) . - Remove 31 bolts (1) and aftercooler housing (2).
Show/hide table
Illustration 2 g06263847 - Attach Tooling (A) and a suitable lifting device to aftercooler housing (4). The weight of aftercooler housing (2) is approximately
27 kg (59.5 lb) . - Remove 25 bolts (3) and aftercooler housing (4).
Show/hide table
| |
| Illustration 1 | g06263843 |
Caterpillar Information System:
C32 XQP1100 Generator Sets Diagnostic Trouble Codes
3516C Petroleum Engine Fuel System - Prime
C9.3B Engines Manifold (Diesel Exhaust Fluid)
C7.1 Marine Propulsion Engine Flywheel Housing - Remove and Install
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Parking
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Mounting and Dismounting
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Alternate Exit
New Engine Software Are Now Used for Certain C27 and C32 Engines {1920} New Engine Software Are Now Used for Certain C27 and C32 Engines {1920}
New Injector Jumper Harness is Now Available for Certain 3406E Truck Engines {1120, 1403} New Injector Jumper Harness is Now Available for Certain 3406E Truck Engines {1120, 1403}
Update on Plastic Plugs for Certain Cat® C13 and C15 Defra Base Generator Sets {1273} Update on Plastic Plugs for Certain Cat® C13 and C15 Defra Base Generator Sets {1273}
301.5, 301.6, 301.7 CR, 301.8 and 302 CR Mini Hydraulic Excavators Seat
New Injector Hold Down Clamps Are Used for Certain C175 Locomotive Engines {1251, 1290} New Injector Hold Down Clamps Are Used for Certain C175 Locomotive Engines {1251, 1290}
G3516 Petroleum Engines Aftercooler - Assemble
C7.1 Marine Propulsion Engine Valve Mechanism Cover - Remove and Install
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Rear Steering) - Disassemble
PM820, PM822, and PM825 Cold Planer Machine Systems Hydraulic Cylinder (Rear Steering) - Assemble
C9.3B Engines Cylinder Liner
C7.1 Marine Propulsion Engine Coolant Level Sensor - Remove and Install
C7.1 Marine Propulsion Engine Coolant Temperature Sensor - Remove and Install
C7.1 Marine Propulsion Engine Engine Oil Pressure Sensor - Remove and Install
C7.1 Marine Propulsion Engine Fuel Pressure Sensor - Remove and Install
C7.1 Marine Propulsion Engine Fuel Temperature Sensor - Remove and Install
C7.1 Marine Propulsion Engine Speed/Timing Sensor - Remove and Install
C7.1 Marine Propulsion Engine Boost Pressure Sensor - Remove and Install