Control Manifold - Disassemble
Start By:
- Remove the control manifold. Refer to Disassembly and Assembly, "Control Manifold - Remove".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (4) and transmission control valves (3).
- Remove main relief valve (5).
- Remove bolts (1) and control manifold (2).
Show/hide table
Illustration 2 g06251294 - Remove O-ring seals (6) and ring seals (9).
- Remove nut (8) and coil assembly (7).
Show/hide table
Illustration 3 g06251324 - Reposition control manifold 180 degrees. Remove relief valve (10) and the O-ring seal.
- Remove relief valve (11) and the O-ring seal.
Show/hide table
Illustration 1 | g06251279 |
Caterpillar Information System:
390F Excavator Machine Systems Position Sensor - Remove and Install - 374F and 390F Stick and Boom Rotary Position Sensor Remove and Install
336, 336 GC and 340 Excavator Systems Cylinder Speed - Check
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Water Spray Lines
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train Hydraulic Tank
320 GC, 320 and 323 Excavator Assist and E-Fence
New Turbochargers and Cartridges Are Now Used for Certain 3500 Marine Engines {1052, 1056} New Turbochargers and Cartridges Are Now Used for Certain 3500 Marine Engines {1052, 1056}
140 Motor Grader Monitoring System
C9.3B Engines for Caterpillar Built Machines Temperature Sensor (Catalyst Inlet) - Remove and Install
336 Excavators (Powered by C9.3 Tier 4 Engine) Engine Supplement Battery - Remove and Install
140 Motor Grader Operator Controls
Rework Procedure of the Coolant Level Wiring Harness on Certain G3306B Generator Sets {1408, 4459, 7422, 7938} Rework Procedure of the Coolant Level Wiring Harness on Certain G3306B Generator Sets {1408, 4459, 7422, 7938}
New Aftercooler Heat Shield Assemblies is Now Used for Certain 3500 Marine Engines {1063, 1073} New Aftercooler Heat Shield Assemblies is Now Used for Certain 3500 Marine Engines {1063, 1073}
320 GC, 320 and 323 Excavator Capacities (Refill)
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Electronic Control Module
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Frame
336 Excavator Machine Systems Bucket Linkage - Remove and Install
CX38–P892 Petroleum Transmission Control Manifold - Assemble
New Digital Voltage Regulator (DVR) Is Now Available {1410, 7620} New Digital Voltage Regulator (DVR) Is Now Available {1410, 7620}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Rotor
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Rotor
XQP1100 Generator Set Voltage Regulators
323F LN Excavator and 323F LN MHPU Machine Systems Machine System
323F LN Excavator and 323F LN MHPU Machine Systems Pilot System
326F and 330F Excavator Machine Systems Main Control Valve