Control Manifold - Assemble
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Inspect the O-ring seals, the seals, and the gaskets. Replace the O-ring seals, the seals, and the gaskets that are worn or damaged.
Note: Lubricate O-ring seals lightly with the lubricant that is being sealed.
- Install relief valve (11) and a new O-ring seal.
- Install relief valve (10) and a new O-ring seal.
Show/hide table
Illustration 2 g06251294 - Install coil assembly (7) and nut (8). Tighten nut (8) to a torque of
6.1 ± 0.7 N·m (54 ± 6.0 lb in) . - Install ring seals (9) and O-ring seals (6).
Show/hide table
Illustration 3 g06251279 Note: Lubricate the bore of main relief valve (5) with the lubricant being sealed.
- Install main relief valve (5). Tighten main relief valve (5) to a torque of
100 ± 10 N·m (74 ± 7.0 lb ft) .Note: Lubricate the bore of transmission control valves (3) with the lubricant being sealed.
- Install transmission control valves (3) and bolts (4). Tighten bolts (4) to a torque of
3.7 ± 0.8 N·m (33 ± 7.0 lb in) . - Install control manifold (2) and bolts (1).
Show/hide table
Illustration 1 | g06251324 |
Note: Lubricate the bores of valves (10) and (11) with the lubricant being sealed.
End By:
- Install the control manifold. Refer to Disassembly and Assembly, "Control Manifold - Install".
Caterpillar Information System:
336 Excavator Machine Systems Bucket Linkage - Remove and Install
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Frame
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Electronic Control Module
320 GC, 320 and 323 Excavator Capacities (Refill)
CX38–P892 Petroleum Transmission Control Manifold - Disassemble
390F Excavator Machine Systems Position Sensor - Remove and Install - 374F and 390F Stick and Boom Rotary Position Sensor Remove and Install
336, 336 GC and 340 Excavator Systems Cylinder Speed - Check
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Water Spray Lines
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Power Train Hydraulic Tank
320 GC, 320 and 323 Excavator Assist and E-Fence
New Turbochargers and Cartridges Are Now Used for Certain 3500 Marine Engines {1052, 1056} New Turbochargers and Cartridges Are Now Used for Certain 3500 Marine Engines {1052, 1056}
140 Motor Grader Monitoring System
New Digital Voltage Regulator (DVR) Is Now Available {1410, 7620} New Digital Voltage Regulator (DVR) Is Now Available {1410, 7620}
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Rotor
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Rotor
XQP1100 Generator Set Voltage Regulators
323F LN Excavator and 323F LN MHPU Machine Systems Machine System
323F LN Excavator and 323F LN MHPU Machine Systems Pilot System
326F and 330F Excavator Machine Systems Main Control Valve
326F and 330F Excavator Machine Systems Negative Flow Control System
326F and 330F Excavator Machine Systems Relief Valve (Main) - Heavy Lift
326F and 330F Excavator Machine Systems Relief Valve (Main)
323F LN Excavator and 323F LN MHPU Machine Systems Boom System
323F LN Excavator and 323F LN MHPU Machine Systems Boom System - SmartBoom Hydraulic System) (If Equipped