Belt - Inspect/Adjust/Replace
Megjegyzés A motor ékszíj-feszítővel van felszerelve, amely automatikusan a helyes értékre állítja be az ékszíj feszességét.
- Nyissa ki, majd emelje fel a motortér fedelét.
Show/hide table
Illusztráció 1 g06206193 (A) Új hajtószíj
(B) Kopott hajtószíj - Vizsgálja meg a csigaszíj állapotát. Idővel a hajtószíj bordáinak anyaga (C) megkopik. A bordák közötti terület megnő (D). Az anyag kopása azt eredményezi, hogy a szíjtárcsa hozzáér a hajtószíj hornyaihoz. Ez a hajtószíj csúszásához és megnövekedett mértékű kopáshoz (E) vezet. Cserélje le a szíjat, ha kopott vagy kirojtosodott.
- Ha az ékszíjat le kell cserélni, végezze el a 3.a - 3.f lépésekben leírt műveleteket.
- Vegye le a felső ventilátorvédőt.
Show/hide table
Illusztráció 2 g06206669 - Forgassa a szíjfeszítőt az óramutató járásával megegyező irányban a szíj leszereléséhez.
- Távolítsa el az ékszíjat.
- Tegyen fel új szíjat.
- Forgassa a szíjfeszítőt az óramutató járásával megegyező irányban a szíj felszereléséhez.
- Tegye vissza a felső ventilátorvédőt.
- Engedje le, majd reteszelje a motortér fedelét.
- Vegye le a felső ventilátorvédőt.
Caterpillar Information System:
Converting from an ABB Turbocharger to a Napier Turbocharger on 3612 Engines Operating on Diesel Fuel {1052, 1061, 1062, 1063, 1071} Converting from an ABB Turbocharger to a Napier Turbocharger on 3612 Engines Operating on Diesel Fuel {1052, 1061, 1062, 1063, 1071}
320GC, 320 and 323 Excavators Machine Systems Main Control Valve - Disassemble
3500 Generator Sets with Dynamic Gas Blending Configuration Parameters
320GC, 320 and 323 Excavators Machine Systems Stick - Remove and Install
3500 Generator Sets with Dynamic Gas Blending Maintenance Recommendations
797F and 797F XQ Off-Highway Trucks Machine Systems Steering Cylinder - Remove and Install - If Equipped with Special Nuts
Replacement Solenoid Valves May Fail on Certain Transmissions {3073, 3167, 3174, 5479, 7499} Replacement Solenoid Valves May Fail on Certain Transmissions {3073, 3167, 3174, 5479, 7499}
3516B Generator Set Engines with Dynamic Gas Blending Fuel Pressure - Diesel System
3500 Generator Sets with Dynamic Gas Blending Overhaul (Top End)
The Hour Meter On Certain Telehandlers, Industrial Engines,and Paving Compactorswith the C3.4B Engine Cannot Be Changed Using Caterpillar Electronic Technician Service Tool {7451} The Hour Meter On Certain Telehandlers, Industrial Engines,and Paving Compactorswith the C3.4B Engine Cannot Be Changed Using Caterpillar Electronic Technician Service Tool {7451}
3516B Generator Set Engines with Dynamic Gas Blending Air Shutoff - Test - No Codes
3516B Generator Set Engines with Dynamic Gas Blending Gas Substitution Percentage Is Low
Coolant Line Is Failing On Certain G3500 Engines {1052, 1380} Coolant Line Is Failing On Certain G3500 Engines {1052, 1380}
Instructions for Sorting and Replacing HVAC Actuators {1800, 7320} Instructions for Sorting and Replacing HVAC Actuators {1800, 7320}
Engine Shutdown Procedure on Certain C4.4 Engines {108I} Engine Shutdown Procedure on Certain C4.4 Engines {108I}
Inspection and Installation of the 285-8515 Bracket on the 353-8989 Radiator Support Assembly for Certain 3516C Generator Sets {1274, 1353} Inspection and Installation of the 285-8515 Bracket on the 353-8989 Radiator Support Assembly for Certain 3516C Generator Sets {1274, 1353}
G3516 Petroleum Engines Prelubrication Oil Pump - Remove and Install
A New NOx Reduction System Cooler Group and Water Lines Group Is Now Used on Certain C15 / C18Tier 4 Commercial Engines {108G} A New NOx Reduction System Cooler Group and Water Lines Group Is Now Used on Certain C15 / C18Tier 4 Commercial Engines {108G}
C11 and C13 Industrial Engines Engine Valve Lash - Inspect/Adjust
797 Off-Highway Truck Steering Link - Remove and Install - If equipped with Special Nuts
C32 Marine Auxiliary Engine Maintenance Interval Schedule
New Engine Software is Now Used for Certain 3516E Engines {1920} New Engine Software is Now Used for Certain 3516E Engines {1920}
Aftertreatment Regeneration on Certain C1.5 and C2.2 Engines {108B, 108E, 108M, 108U} Aftertreatment Regeneration on Certain C1.5 and C2.2 Engines {108B, 108E, 108M, 108U}
PM820, PM822, and PM825 Cold Planer Machine Systems Track Roller - Remove and Install