Water Pump - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
D | 1P-0510 | Driver Group | 1 |
E | 138-9299(1) | Oil Seal Tool | 1 |
E | FT-3171(2) | Oil Seal Tool | 1 |
F | 139-0088(1) | Seal Tool | 1 |
F | 325-5756(2) | Seal Tool | 1 |
Show/hide table
(1) | Use with a |
(2) | Use with a |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Clean water pump shaft (6) and the counterbore for lip seal (9) in housing (1).
- Use Tooling (D) to install a new lip seal (9) in housing (1).
Note: Install the seal with the part number on the metal face of the seal toward the housing. Ensure that the lip seal is flush with the front edge of the counterbore of the housing. Do not lubricate the lip seal. Use a press to install the lip seal. Do not install the lip seal by hand.
- Install bearing assembly (8) on water pump shaft (6).
- Place retainer (5) with “OUTSIDE” markings toward the gear end of water pump shaft (6).
- Use a press and install gear (2) on water pump shaft (6).
Note: Install gear (2) against bearing assembly (8).
- Slide Tooling (E) over shaft (6). The tapered edge will be facing outward.
- Install gear (2) and the water pump shaft into housing (1). Use care not to damage lip seal (9). Install bolts (3) that hold bearing retainer (5) to the housing.
- Remove Tooling (E) from water pump shaft (6).
- Use a press and Tooling (F) to install a new seal group (7) over shaft (6) and into housing (1). Ensure that the outer shell of the seal is fully seated in the housing.
- Put impeller (4) in position on water pump shaft (6). Use a press and install impeller (4) on the water pump shaft.
Note: Install impeller (4) within
0.00 ± 0.25 mm (0.000 ± 0.010 inch) of the end of the water pump shaft. - Install O-ring seal (10) on the housing.
Show/hide table
Illustration 1 | g01021798 |
End By:
- Install the water pump.
Caterpillar Information System:
C18 Generator Set Engines Water Pump - Disassemble
3516C Generator Set Engines Turbocharger - Install
® Grade & Slope for Cold Planers Grade Control Guidance Screen
C9.3 Marine Auxiliary Engines Maintenance Interval Schedule - Marine Generator Set
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Auxiliary Hydraulic System Troubleshooting
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Visual Inspection (Auxiliary Hydraulic System)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Machine Preparation for Troubleshooting
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Propel System Troubleshooting
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Visual Inspection (Power Train)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Machine Preparation for Troubleshooting
The Model Directory for Authorized Classic Machines has been Updated {1000, 7000} The Model Directory for Authorized Classic Machines has been Updated {1000, 7000}
High Fuel Rail Pressure Alarm May Malfunction on Certain Generator Sets {7610, 7620} High Fuel Rail Pressure Alarm May Malfunction on Certain Generator Sets {7610, 7620}
Product Link For Generator Sets Parameters
C18 Generator Set Engines Water Temperature Regulator Housing - Remove and Install
C18 Generator Set Engines Flywheel - Remove and Install
XQP150 Rental Generator Set Product Description
XQP150 Rental Generator Set Plate Locations and Film Locations
XQP150 Rental Generator Set Plate Locations and Film Locations
C18 Generator Set Engines Crankshaft Rear Seal - Remove and Install
G3516B Engines Fuel Metering Valve
C175-20 Locomotive Engine Filter Screen (Air) - Inspect/Clean
3512E Engines Accessory Drive (Front) - Remove and Install
C18 Generator Set Engines Flywheel Housing - Remove and Install
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Conveyor (First Stage) - Test - Case Drain Flow for Piston Motor