Turbocharger - Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | Loctite C5-A 铜基抗咬合润滑剂 | - |
注: 对于用螺栓固定的排气歧管,排气卡箍上不要使用工具 (A)。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
注意 |
---|
卡箍组件应只使用一次。 使用后弃置所有卡箍组件。 |
Show/hide table
注意 |
---|
波纹管组件应只使用一次。 使用后弃置所有波纹管。 |
- 将适当起吊设备连在涡轮增压器 (43) 上。 涡轮增压器 (43) 的重量约为
135 kg (300 lb) 。 - 将涡轮增压器 (43) 放置在安装支架上。 将工具 (A) 涂敷在螺栓 (45) 的螺纹上。 安装螺栓 (45)。 此时请勿拧紧螺栓 (45)。
- 安装管组件 (44)。 连接管 (49)、管组件 (48) 和管组件 (46)。
注: 在安装过程中,确保波纹管组件处于正确的朝向。 波纹管组件的顶部之间间距应相等
- 将工具 (A) 涂抹在螺纹、轴承表面以及卡箍组件 (47) 的内表面。
- 安装新的波纹管组件 (50)、螺栓 (51) 以及新的卡箍组件 (47)。 拧紧卡箍组件 (47) 至扭矩为
10 ± 1 N·m (90 ± 9 lb in) 。 用软锤在卡箍组件的直径四周轻轻敲打。 拧紧卡箍组件 (47) 至扭矩为10 ± 1 N·m (90 ± 9 lb in) 。Show/hide table图 2 g06059301 注: 在安装过程中,确保波纹管组件处于正确的朝向。 流向箭头的方向应指向正确的方向。 波纹管组件的顶部之间间距应相等
- 将工具 (A) 涂抹在螺纹、轴承表面以及卡箍组件 (41) 和卡箍组件 (40) 的内表面上。
- 将新的波纹管组件、新的卡箍组件 (41) 和新的卡箍组件 (40) 安装在涡轮增压器 (42) 上。 将卡箍组件 (41) 和卡箍组件 (40) 拧紧至扭矩为
7.5 ± 1.0 N·m (65 ± 9 lb in) 。 用软面锤轻轻敲打卡箍组件外缘。 将卡箍组件 (41) 和卡箍组件 (40) 拧紧至扭矩为7.5 ± 1.0 N·m (65 ± 9 lb in) 。 - 拧紧螺栓 (45)。
Show/hide table
图 3 g06074770 - 安装护罩组件 (38) 和螺栓 (39)。
Show/hide table
图 4 g06074764 - 安装支架 (36) 和螺栓 (37)。
Show/hide table
图 5 g06074733 - 安装支架 (34) 和螺栓 (33)。
- 安装温度传感器 (35)。
Show/hide table
图 6 g06074704 - 安装支架 (31) 和螺栓 (30)。
- 安装温度传感器 (32)。
Show/hide table
图 7 g06074573 - 安装护罩组件 (29) 和螺栓 (28)。
Show/hide table
图 8 g06074557 - 安装螺栓 (27)。
Show/hide table
图 9 g06074285 - 安装护罩组件 (26) 和螺栓 (25)。
Show/hide table
图 10 g06074281 - 安装护罩组件 (23) 和螺栓 (24)。
Show/hide table
图 11 g06074279 - 安装护罩组件 (21) 和 (22)。
- 安装螺栓 (19) 和螺栓 (20)。
Show/hide table
图 12 g06074274 - 安装支架 (17)、支架 (18) 和螺栓 (16)。
Show/hide table
图 13 g06074229 - 连接管路 (15)。
Show/hide table
图 14 g06074144 - 安装盖 (13) 和螺栓 (14)。
Show/hide table
图 15 g06045908 - 安装护罩组件 (12)。
Show/hide table
图 16 g06045883 - 安装护罩组件 (9)。
- 连接弹簧组件 (10)。
Show/hide table
图 17 g06045879 - 安装护罩组件 (7)。
- 连接弹簧组件 (8)。
Show/hide table
图 18 g06045853 - 安装护罩组件 (6)。
- 连接弹簧组件 (5)。
Show/hide table
图 19 g06045816 - 安装空气滤清器组件 (2)。
- 安装螺栓 (4)。
- 连接软管 (1) 并松开卡箍 (3)。
- 向冷却系统加注冷却液。 请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
Show/hide table
图 1 | g06059308 |
Caterpillar Information System:
® Grade & Slope for Cold Planers Grade Control Guidance Screen
C9.3 Marine Auxiliary Engines Maintenance Interval Schedule - Marine Generator Set
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Auxiliary Hydraulic System Troubleshooting
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Visual Inspection (Auxiliary Hydraulic System)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Machine Preparation for Troubleshooting
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Propel System Troubleshooting
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Visual Inspection (Power Train)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Machine Preparation for Troubleshooting
The Model Directory for Authorized Classic Machines has been Updated {1000, 7000} The Model Directory for Authorized Classic Machines has been Updated {1000, 7000}
High Fuel Rail Pressure Alarm May Malfunction on Certain Generator Sets {7610, 7620} High Fuel Rail Pressure Alarm May Malfunction on Certain Generator Sets {7610, 7620}
G3600 Engines Maintenance Interval Schedule
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Relief Valve (Charge) - Test - Conveyor
C18 Generator Set Engines Water Pump - Disassemble
C18 Generator Set Engines Water Pump - Assemble
Product Link For Generator Sets Parameters
C18 Generator Set Engines Water Temperature Regulator Housing - Remove and Install
C18 Generator Set Engines Flywheel - Remove and Install
XQP150 Rental Generator Set Product Description
XQP150 Rental Generator Set Plate Locations and Film Locations
XQP150 Rental Generator Set Plate Locations and Film Locations
C18 Generator Set Engines Crankshaft Rear Seal - Remove and Install
G3516B Engines Fuel Metering Valve
C175-20 Locomotive Engine Filter Screen (Air) - Inspect/Clean
3512E Engines Accessory Drive (Front) - Remove and Install