Rocker Arm and Shaft - Remove and Install
Start By:
- Remove valve mechanism cover.
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 487-3136 | Rocker Shaft Removal and Installation Tool | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove clip (1).
Show/hide table
Illustration 2 g06113004 - Install Tooling (A) to and attach a suitable lifting device to rocker arm assembly (2). Rocker arm assembly (2) weighs approximately
13 kg (29 lb) .Show/hide tableIllustration 3 g06044952 - Loosen bolts (4) and remove bolts (3). Use Tooling (A) and a suitable lifting device to remove rocker arm assembly (2). The weight of rocker arm assembly (2) is approximately
37 kg (81 lb) . Remove valve blocks (5).
Show/hide table
Illustration 1 | g06044402 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install rocker arm assembly (2) in the reverse order of removal.
- Tighten bolts (3) to a torque of
25 N·m (221 lb in) using the following tightening sequence. Then, tighten bolts (3) to a torque of60 N·m (44 lb ft) using the same tightening sequence. Next, tighten bolts (3) to a torque of80 N·m (59 lb ft) using the same tightening sequence. Finally, tighten bolts (3) an extra 60 degrees. - Adjust the valve lash of the rocker arms. Refer to Test and Adjust, "Engine Valve Lash - Inspect/Adjust" for the correct procedure.
Show/hide tableIllustration 4 g06045630 - Tighten bolts (3) to a torque of
Caterpillar Information System:
Proper Storage Procedures Are Available For Commercial Engines {1000} Proper Storage Procedures Are Available For Commercial Engines {1000}
Product Link For Generator Sets Features
C12.9 Marine Engines Fuel Lines - Remove and Install
C12.9 Marine Engines Electronic Unit Injector - Remove and Install
3608 Engine Connecting Rod
3516C Generator Set Engines Turbocharger - Remove
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Relief Valve (Auxiliary) - Test and Adjust - Auxiliary Power Unit
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Pressure Reducing Valve - Test and Adjust - Right Grade Ski Control
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Steering Angle - Calibrate
A New Sea Water Pump and Seal Collars Are Available for Certain C32 Marine Engines {1371} A New Sea Water Pump and Seal Collars Are Available for Certain C32 Marine Engines {1371}
TR35 Railway Transmission Output Transfer Gears
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Pressure Reducing Valve - Test and Adjust - Left Grade Control Ski
Beat In and Wear at the Clutch Plate Splines on Certain CX31 Transmissions {0374, 0599, 3030, 3050, 3064, 3160, 3190} Beat In and Wear at the Clutch Plate Splines on Certain CX31 Transmissions {0374, 0599, 3030, 3050, 3064, 3160, 3190}
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Travel Speed - Test
XQP150 Rental Generator Set Electrical System
XQP150 Rental Generator Set Generator Isolating for Maintenance
C9.3 Industrial Engine Selective Catalytic Reduction Warning System
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Relief Valve (Charge) - Test - Conveyor
G3600 Engines Maintenance Interval Schedule
High Fuel Rail Pressure Alarm May Malfunction on Certain Generator Sets {7610, 7620} High Fuel Rail Pressure Alarm May Malfunction on Certain Generator Sets {7610, 7620}
The Model Directory for Authorized Classic Machines has been Updated {1000, 7000} The Model Directory for Authorized Classic Machines has been Updated {1000, 7000}
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Machine Preparation for Troubleshooting
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Visual Inspection (Power Train)
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Propel System Troubleshooting