Engine Oil Pan - Assemble
Show/hide table
Required Tooling | |||
Tool | Part Number | Part Description | Qty |
A | - | Loctite 596 RTV Silicone High Temp | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install oil screen housing (16) and bolts (17).
- Lightly lubricate the bores of tube assembly (18) and oil screen handle (15) with the fluid that is being sealed. Install tube assembly (18) and oil screen handle (15).
Show/hide table
Illustration 2 g06040050 - Install plug (14) and plugs (13).
- Install cover (12) and bolts (11).
Show/hide table
Illustration 3 g06040033 - Install pipe plug (6), cover (10), cover (7), bolts (9), and bolts (8).
Show/hide table
Illustration 4 g06040280 - Install plate (5) and bolts (4). Tighten bolts (4) marked (X) first, then tighten bolts (4) in the sequence shown in illustration 4.
- Apply Tooling (A) to the gasket. Install the gasket, oil pan (2), and bolts (3).
- Install drain plug (1). Tighten drain plug (1) to a torque of
145 ± 15 N·m (107 ± 11 lb ft) .
Show/hide table
Illustration 1 | g06040097 |
End By:
- Install engine oil pan.
Caterpillar Information System:
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System System Pressure - Release
A Hose Assembly for the Fast Fill Fuel Adapter Group has been Updated on Certain G Series Small Off-Highway Trucks {0782, 1710, 7554} A Hose Assembly for the Fast Fill Fuel Adapter Group has been Updated on Certain G Series Small Off-Highway Trucks {0782, 1710, 7554}
C18 Generator Set Engines Inlet and Exhaust Valves - Remove and Install
TR35 Railway Transmission Speed Sensor
XQP150 Rental Generator Set Generator Operation
XQP150 Rental Generator Set Single Unit Operation
3512E Tier 4 Final Engines for Land Electric Drilling Fuel Injector
C18 Generator Set Engines Inlet and Exhaust Valve Springs - Remove and Install
C175 Generator Sets Overhaul (Top End)
3512E Engines Engine Oil Pan - Disassemble
C18 Generator Set Engines Air Inlet Elbow - Remove and Install
C18 Generator Sets Voltage Regulators
XQP150 Rental Generator Set Battery Disconnect Switch
C18 Generator Set Engines Inlet and Exhaust Valve Guides - Remove and Install
TR35 Railway Transmission Temperature Sensor (Transmission Oil)
DG30, DG50, DG60, DG80, DG100, DG125, and DG150 Generator Set Engines Basic Engine
PM620, PM622, PM820, PM822 and PM825 Cold Planer Machine System Hydraulic Oil Contamination - Test
New Flywheels Are Now Used on Certain G3500 Engines {1156} New Flywheels Are Now Used on Certain G3500 Engines {1156}
TR35 Railway Transmission Torque Converter
3512E Engines Engine Oil Scavenge Pump - Remove and Install
The Reuse and Salvage Guidelines for HVOF Cylinders has been Updated {0599, 0679, 0738, 4303, 5102, 7562} The Reuse and Salvage Guidelines for HVOF Cylinders has been Updated {0599, 0679, 0738, 4303, 5102, 7562}
PM620, PM622, PM820, PM822 and PM825 Cold Planer Propel Systems Relief Valve (Charge) - Test and Adjust - Propel
C13, C15, and C18 Tier 4 Final Engines Diesel Exhaust Fluid Tank
C12.9 Marine Engines Cylinder Head - Remove and Install