DEF Injector and Mounting - Remove and Install
Show/hide table
Illustration 1 | g03376713 |
Show/hide table
Specification for 399-6078 DEF Injector & Mounting Gp | |||
Item | Qty | Part | Specification Description |
1 | 3 | 380-8418 Bolt | Use the following procedure to tighten the bolt : Before assembly, lubricate the threads with Loctite Nickel Anti-Seize. 1. Tighten the bolts to 2. Again, tighten the bolts to 3. Turn an additional angle of 90 ± 5 degrees. |
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 385-1861 | Connector Plug | 2 |
B | - | Loctite Nickel Anti-seize | - |
- Disconnect harness assembly (1), harness assembly (2), and hose assemblies (3). Cap hose assemblies (3) with Tooling (A).
Show/hide table
Illustration 3 g06027883 Show/hide tableIllustration 4 g06027892 - Remove bolts (3).
- Remove DEF injector assembly (5) and gasket (4). Discard gasket (4) and seal (6) from DEF injector assembly (5).
Show/hide table
Illustration 2 | g06027882 |
- Install DEF injector assembly (5) in the reverse order of removal.
Note: To maintain cleanliness, the protective caps must remain in place until the final fluid connections are made.
Note: Install gasket (4) so the metal is toward the Diesel Exhaust Filter Group.
- Replace gasket (4) with a new gasket. Replace seal (6) with a new seal.
- Apply Tooling (B) to the threads of bolts (3).
- Tighten bolts (3) to a torque of
5.0 ± 0.5 N·m (44 ± 4 lb in) . - Retighten bolts (3) to a torque of
5.0 ± 0.5 N·m (44 ± 4 lb in) . Turn an extra 90°±5°.
Caterpillar Information System:
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Steering Control Group
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Control Valve and Mounting
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Check Valve
745 and 740 GC & 740 EJECTOR Articulated Truck Systems Check Valve
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Track Roller (Single Flange)
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Electronic Control Module
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Steering Lines
C12.9 Marine Engines Crankshaft Pulley - Remove and Install
C175-16 and C175-20 Locomotive Engines Turbocharger - Install
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Machine Electronic Control Module Mounting
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Operator Console
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Track Tension Lines
C18 Generator Set Engines Manifold (DEF Heater) - Remove and Install
Exhaust Manifold for Certain C1.5 Marine Generator Sets {1059} Exhaust Manifold for Certain C1.5 Marine Generator Sets {1059}
C1.7 and C2.2 Industrial Engine Relay - Test - Fan Drive Relay
C12.9 Marine Engines Water Pump - Remove and Install
C12.9 Marine Engines Crankcase Breather - Remove and Install
C7.1-XQ230 Rental Generator Set Before Starting Engine
C7.1-XQ230 Rental Generator Set General Hazard Information
C18 Generator Set Engines Voltage Control (Load Protection) - Remove and Install
C12.9 Marine Engines Fuel Filter Base - Remove and Install
C12.9 Marine Propulsion Engine Belt Tensioner
C1.7 and C2.2 Industrial Engine Relay - Test - Fuel Lift Pump Relay
UPS 750 Uninterruptible Power Supply Oil - Change