Fuel Filter Housings - Remove and Install
Start By:
- Remove the water temperature regulator housing.
- Remove the fuel filter elements.
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect tube assemblies (1). Remove the O-ring seals. Attach a suitable lifting device to fuel filter housing (2). The weight of fuel filter housing (3) is approximately
90 kg (198 lb) .Show/hide table
Illustration 2 g03841518 - Remove bolts (3) from both sides of fuel filter housing (2) and remove fuel filter housing (2).
Show/hide table
| |
| Illustration 1 | g03841516 |
- Install fuel filter housing (2) in the reverse order of removal.
Caterpillar Information System:
3412 Generator Set Oil Pressure Is Low
794 AC Off-Highway Truck Field Assembly Front Axle - Install
2015/06/12 A New Speed Controller and Actuator Are Available for Certain G3400 and G3500 Engines {1264, 1908}
3412 Generator Set Engine Top Speed Is Not Obtained
C280-08 Tier 4 Engine Water Pump Seal - Remove
2015/05/29 Cat® Reman Announces the Availability of Remanufactured Fuel Check Valves Assemblies for G3600 Engines {1106}
2015/06/26 Cat® Reman Is Announcing an Appearance Change to the EI550 Classic, Bridge, and ACERT Electronic Unit Injectors for Certain Truck Engines {1290}
2015/06/05 Cat Reman Is Announcing an Appearance Change to the EI550 Classic, Bridge, and ACERT Electronic Unit Injectors for Certain Commercial Engines {1290}
2015/06/04 Cat® Reman Is Announcing an Appearance Change to the EI550 Classic, Bridge, and ACERT Electronic Unit Injectors for Certain Machine Engines {1290}
C280-08 Tier 4 Engine Water Pump Seal - Install
797F Off-Highway Truck Field Assembly Automatic Lubrication - Install - Service Center
C280-08 Tier 4 Engine Prelubrication Oil Pump - Assemble
3512C Generator Set Engine Turbocharger - Disassemble
3512C Generator Set Engine Turbocharger - Assemble
3412 Generator Set Power Is Intermittently Low or Power Cutout Is Intermittent
Reuse & Salvage Procedure for Off-Highway Truck Accumulators {0374, 0599, 0679, 0738, 4269, 4331, 5077} Reuse & Salvage Procedure for Off-Highway Truck Accumulators {0374, 0599, 0679, 0738, 4269, 4331, 5077}
3516C Generator Set Engines Air Shutoff - Remove and Install
349F and 352F Excavators Machine System Specifications Pump Coupling
3512C Engines for 785C Off-Highway Trucks with Dynamic Gas Blending Electrical Power Supply - Test
3412 Generator Set Sensor Signal (Analog, Active) - Test
C280-08 Tier 4 Engine Priority Valve - Remove and Install
2015/06/23 A New Information Display is Now Used For Certain Cat® Products {7490}
2015/06/05 Recommendations for Cold Weather Operation for C7.1 Generator Set {1225, 1317, 1331}
C280-08 Tier 4 Engine Flywheel and Ring Gear - Remove and Install