Oil Temperature Regulators - Remove and Install
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 1P-0510 | 冲头总成 | 1 |
Show/hide table
| 注意 |
|---|
|
在检查、保养、测试、调整及维修产品时，请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前，请准备好盛接液体用的适当容器。 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 放掉发动机机油。 有关正确的排放和加注步骤，请参阅操作和保养手册, "发动机机油和滤清器 - 更换"。
Show/hide table
图 1 g03809340 - 拆下螺栓 (1)、螺栓 (3)、盖 (2) 和密封垫。
Show/hide table
图 2 g03809366 - 将适当的起吊设备连接到调节器壳体 (6) 上。
- 拆下螺栓 (4)、螺栓 (5)、螺栓 (7) 和调节器壳体 (6)。 调节器壳体 (6) 的重量约为
23 kg (51 lb) 。Show/hide table
图 3 g03809391 - 拆下机油温度调节器 (8) 和唇形密封 (9)。
- 按与拆卸相反的顺序安装机油温度调节器 (8)。
- 使用工具 (A) 安装唇形密封 (9)。
- 使用密封的润滑剂润滑盖 (2) 的孔。
Caterpillar Information System:
2015/04/10 Updated Torque Requirements for Reman Rocker Arm Adjusting Screw Lock Nuts on Certain C15, C16, and C18 Truck Engines {1123}
2015/04/03 Updated Torque Requirements for Reman Rocker Arm Adjusting Screw Lock Nuts on Certain C15, C16, C18, C27, and C32 Engines {1123}
2015/03/31 Updated Torque Requirements for Reman Rocker Arm Adjusting Screw Lock Nuts on Certain C15, C18, C27, and C32 Machine Engines {1123}
C7.1 Marine Generator Set Power Sources
C7.1 Marine Generator Set Cooling System - Check - Overheating
C7.1 Marine Generator Set Turbocharger - Inspect
C7.1 Marine Generator Set Electronic Control System
C7.1 Marine Generator Set Fuel Injection
C7.1 Marine Generator Set Cooling System
C7.1 Marine Generator Set Air Inlet and Exhaust System
C7.1 Marine Generator Set Electrical System
C7.1 Marine Generator Set V-Belt - Test
C9.3 Marine Auxiliary and Generator Set Engine Exhaust System Contains Coolant
C9.3 Marine Auxiliary and Generator Set Engine Exhaust System Contains Oil
G3612 and G3616 Engines Priority Valve - Remove and Install
C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
Coolant Diverters for the NRS Cooler Are Being Left Out after Servicing C9.3 Tier 4 Interim and Final Engines{108C, 135D} Coolant Diverters for the NRS Cooler Are Being Left Out after Servicing C9.3 Tier 4 Interim and Final Engines{108C, 135D}
C2.2 Engines for Caterpillar Built Machines Crankshaft - Install
C2.2 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting Rods in Position
G3612 and G3616 Engines Priority Valve - Disassemble
C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install - Connecting Rods in Position
C2.2 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
C2.2 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install