Priority Valve - Remove and Install
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
当发动机变热时,不要拆下优先阀。 热油能造成烫伤。 |
- 放掉发动机机油。 有关正确的排放和加注步骤,请参阅操作和保养手册, "发动机机油和滤清器 - 更换"。
Show/hide table
图 1 g03809448 - 断开线束组件 (1)、线束组件 (2) 和线束组件 (3)。
- 拆下螺栓 (4)、螺栓 (6)、螺栓 (5) 和线束组件 (7)。
Show/hide table
图 2 g03809475 - 拆下螺栓 (8)、螺栓 (9) 和弯头 (10)。
Show/hide table
图 3 g03809496 - 拆下螺栓 (11)、螺栓 (13) 和管组件 (12)。
Show/hide table
图 4 g03809822 - 连接适当的起吊设备以拆下优先阀 (15)。
- 拆下螺栓 (14) 和优先阀 (15)。 优先阀 (15) 的重量约为
34 kg (75 lb) 。
- 按与拆卸相反的顺序安装优先阀 (15)。
- 润滑管组件 (12) 和弯头 (10) 的孔。
Caterpillar Information System:
C9.3 Marine Auxiliary and Generator Set Engine Exhaust System Contains Oil
C9.3 Marine Auxiliary and Generator Set Engine Exhaust System Contains Coolant
G3612 and G3616 Engines Oil Temperature Regulators - Remove and Install
2015/04/10 Updated Torque Requirements for Reman Rocker Arm Adjusting Screw Lock Nuts on Certain C15, C16, and C18 Truck Engines {1123}
2015/04/03 Updated Torque Requirements for Reman Rocker Arm Adjusting Screw Lock Nuts on Certain C15, C16, C18, C27, and C32 Engines {1123}
2015/03/31 Updated Torque Requirements for Reman Rocker Arm Adjusting Screw Lock Nuts on Certain C15, C18, C27, and C32 Machine Engines {1123}
C7.1 Marine Generator Set Power Sources
C7.1 Marine Generator Set Cooling System - Check - Overheating
C7.1 Marine Generator Set Turbocharger - Inspect
C7.1 Marine Generator Set Electronic Control System
C7.1 Marine Generator Set Fuel Injection
C7.1 Marine Generator Set Cooling System
C2.2 Engines for Caterpillar Built Machines Crankshaft - Remove
Coolant Diverters for the NRS Cooler Are Being Left Out after Servicing C9.3 Tier 4 Interim and Final Engines{108C, 135D} Coolant Diverters for the NRS Cooler Are Being Left Out after Servicing C9.3 Tier 4 Interim and Final Engines{108C, 135D}
C2.2 Engines for Caterpillar Built Machines Crankshaft - Install
C2.2 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Remove - Connecting Rods in Position
G3612 and G3616 Engines Priority Valve - Disassemble
C2.2 Engines for Caterpillar Built Machines Connecting Rod Bearings - Install - Connecting Rods in Position
C2.2 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Remove
C2.2 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
C2.2 Engines for Caterpillar Built Machines Crankshaft Gear - Remove and Install
C2.2 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
C9 Generator Set Product Installation