Auxiliary Water Pump - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | - | Guide Bolt 1/2 - 13 NC by 4 inch |
2 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Drain the coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.
- Disconnect the connection for the auxiliary water inlet. Cap the openings.
Show/hide table
Illustration 1 g03743076 - Remove tube (1) and elbow (4). Remove tube (2) and elbow (3). Remove the O-ring seals and the gaskets (not shown).
Show/hide table
Illustration 2 g03743085 - Attach a suitable lifting device to auxiliary water pump (5). The weight of auxiliary water pump (5) is approximately
55 kg (120 lb) . - Remove two bolts (6). Install Tooling (A) and remove remaining bolts (6). The weight of auxiliary water pump (5) is approximately
25 kg (55 lb) . Using two people, remove auxiliary water pump (5). - Remove the O-ring seal from the joint between the auxiliary water pump and the front housing. Discard the O-ring seal.
- Install auxiliary water pump (5) in the reverse order of removal.
- Install a new O-ring seal to the joint between the auxiliary water pump and the front housing.
- Lubricate the O-ring seal prior to installing the auxiliary water pump.
Caterpillar Information System:
3516C HD Generator Set with Gearbox Belts - Inspect/Adjust/Replace
Cat® Command For Hauling MID 039 - CID 3456 - FMI 03
Cat® Command For Hauling MID 039 - CID 3454 - FMI 05
C280 Petroleum Engine Fuel Filter Housings - Remove and Install
C13 Industrial Engine Monitoring System
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Check Valve
Fuel Filtration Kits Used for Migrated Commercial Engines{1258, 1260} Fuel Filtration Kits Used for Migrated Commercial Engines{1258, 1260}
C280-08 Tier 4 Engine Auxiliary Water Pump - Assemble
C280-08 Tier 4 Engine Auxiliary Water Pump - Disassemble
C7.1-XQ200 Rental Generator Set Maintenance Interval Schedule - Standby
Speed Instability Issues on 3512Well Service Engines Equipped with Cat® Transmission and Dynamic Gas Blending Kit {7620} Speed Instability Issues on 3512Well Service Engines Equipped with Cat® Transmission and Dynamic Gas Blending Kit {7620}
C7.1-XQ200 Rental Generator Set Maintenance Interval Schedule - Prime
2015/05/29 A New Torque Procedure for Connecting Rod Bolts Is Now Used on 3600, G3600, and C280 Engines {1218}
2014/12/24 A New Water Pump Oil Seal is Used on 3600, G3600, and C280 Engines {1361, 7555}
C4.4 Engines Welding Precaution
C280 Marine Engines SCR Catalyst Inlet Pressure Is High
C280 Marine Engines SCR Catalyst Inlet Pressure Is Low
C4.4 and C7.1 Engines Electronic Service Tools
XQ375 and XQ425 Rental Generator Sets Model View Illustrations
C4.4 and C7.1 Engines Service Information Report
C4.4 Engines System Overview
C7.1 Engines Component Location
Mechanical Application and Installation Guide for the CX31-P600 Petroleum Transmission {3030} Mechanical Application and Installation Guide for the CX31-P600 Petroleum Transmission {3030}
XQC1600 Power Module Fuel System - Prime