Flow Control Valve - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 388-1289 | 封盖套件 | 1 |
Show/hide table
接触高压燃油可能导致液体渗透和烧伤危险。 高压燃油溢出可能会产生火灾。 如果不遵循检查、保养和维修指南,可能会造成人身伤亡。 |
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅系统运作,测试和调整, "燃油系统部件清洁度"。 |
- 将燃油供应转到断开位置。
- 将蓄电池断路开关转到断开位置。
Show/hide table
图 1 g02539836 - 清洁流量控制阀 (2) 和喷油泵周围的区域。 开始组装前,确保该区域无污染。
- 将线束组件 (3) 从流量控制阀 (2) 上断开。
- 在流量控制阀和喷油泵上作临时标记,以便安装。
- 将六角头螺钉 (1) 从流量控制阀上拆下。
- 将流量控制阀从喷油泵上拆下。
- 用工具 (A) 塞住喷油泵。
- 拆下 O 形密封圈 (4)(未显示)。
- 确保所有部件无磨损或损坏。 如果流量控制阀的任何部位磨损或损坏,则必须将流量控制阀作为组件更换。
Show/hide table
图 2 g02539836 - 将新 O 形密封圈 (4)(未显示)定位到流量控制阀组件上。
- 检查 O 形密封圈 (4)(未显示)是否正确就位。 确保 O 形密封圈未损坏。
- 使用清洁的燃油润滑 O 形密封圈 (4)(未显示)。
注: 确保 O 形密封圈未损坏或对偏。
- 将工具 (A) 从喷油泵上拆下。
- 将流量控制阀 (3) 安装到喷油泵上。
- 安装流量控制阀修理套件中的所有六角头螺钉 (2)。
- 均匀拧紧六角头螺钉 (2),直到流量控制阀正确落座在燃油泵上。
注: 确保六角头螺钉均匀拧紧。 不能确保六角头螺钉均匀拧紧会导致喷油泵损坏。
- 拧紧六角头螺钉至扭矩为
9 N·m (80 lb in) 。 - 将线束组件 (1) 连接到流量控制阀 (3) 上。
- 更换燃油系统粗滤器。 有关正确步骤,请参阅操作和保养手册, "燃油系统粗滤(水分离器)滤芯 - 更换"。
- 更换燃油系统细滤器。 参考操作和保养手册, "燃油系统细滤器 - 更换"以了解正确步骤。
- 将燃油供应转到接通位置。
- 将蓄电池断路开关转到接通位置。
- 排出燃油系统中的空气。 有关更多信息,请参阅操作和保养手册, "燃油系统 - 充油"。
结束:
- 更换流量控制阀后,需要对喷油泵执行高压燃油泵标定步骤。 有关正确步骤,请参阅故障诊断与排除, "燃油油轨压力故障"。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490} Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490}
Procedure for Seismic Anchor Installation of Multi Module Systems{4480} Procedure for Seismic Anchor Installation of Multi Module Systems{4480}
XQC1200 and XQC1600 Power Modules Exhaust Elbow - Remove and Install
455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000}
C27 and C32 Generator Set Engines Electronic Control Module - Remove and Install
C27 and C32 Generator Set Engines Turbocharger Outlet Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Fuel Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Fuel Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Engine Oil Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Coolant Temperature Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C3.4B Engines for Caterpillar Built Machines Water Separator and Fuel Filter (Primary) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Injection Lines - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Lines - Install
C3.4B Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Throttle Valve (Intake Air) - Remove and Install - Rear Facing Inlet Elbow
C3.4B Engines for Caterpillar Built Machines Throttle Valve (Intake Air) - Remove and Install - Side Facing Inlet Elbow
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Install