Throttle Valve (Intake Air) - Remove and Install - Rear Facing Inlet Elbow
- 松开软管卡箍,并将软管组件从弯头 (1) 上断开。
- 将锁片滑入解锁位置,并将线束组件 (7) 从节气门 (8) 上断开。
- 松开软管卡箍 (2),然后将软管组件 (4) 从弯头 (1) 上断开。
- 将螺栓 (5) 和螺母 (3) 从弯头上拆下。
- 将进气弯头从螺柱 (9) 上拆下。
- 拆下密封垫 (6)(未显示)。
- 将节气门 (8) 从螺柱 (9) 上拆下。
- 拆下密封垫 (6)(未显示)。
- 如有必要,卸下螺柱 (9)。 有关正确步骤,请参阅拆解和装配, "进气歧管 - 拆卸和安装"。
Show/hide table
图 3 g02906404 - 如有必要,将适配器 (12) 和密封垫圈 (11) 从弯头 (1) 上拆下。
Show/hide table
图 1 | g02906277 |
Show/hide table
图 2 | g02906317 |
- 检查所有部件有无磨损和损坏。 如有必要,更换所有磨损或损坏的部件。
Show/hide table
图 4 g02906404 Show/hide table图 5 g02906317 Show/hide table图 6 g02906277 - 如有必要,安装螺柱 (9) 。 有关正确步骤,请参阅拆解和装配, "进气歧管 - 拆卸和安装"。
- 如有必要,将新密封垫圈 (11) 安装到适配器 (12) 上。 拧紧适配器至扭矩为
20 N·m (177 lb in) 。 - 将密封垫 (10) 安装到螺柱 (9) 上。
- 将节气门 (8) 安装到螺柱 (9) 上。
- 将密封垫 (6) 安装到螺柱 (9) 上。
- 将弯头 (1) 安装到螺柱 (9) 上。
- 安装螺栓 (5) 并用手拧紧。
- 安装螺栓 (3) 并用手拧紧。
- 拧紧螺栓 (5) 和螺母 (3) 至扭矩为
10 N·m (89 lb in) 。 - 将软管卡箍 (2) 定位到软管组件 (4) 上。 将软管组件 (4) 安装到适配器 (12) 上,并牢固拧紧软管卡箍 (2)。
- 将线束组件 (7) 安装到节气门 (8) 上。 将锁片滑入锁定位置。
- 将卡箍安装到进气软管上,并将进气软管连接到弯头 (1) 上。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Injection Lines - Install
C3.4B Engines for Caterpillar Built Machines Fuel Injection Lines - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Water Separator and Fuel Filter (Primary) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C3.4B Engines for Caterpillar Built Machines Flow Control Valve - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490} Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490}
Procedure for Seismic Anchor Installation of Multi Module Systems{4480} Procedure for Seismic Anchor Installation of Multi Module Systems{4480}
XQC1200 and XQC1600 Power Modules Exhaust Elbow - Remove and Install
455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000}
C3.4B Engines for Caterpillar Built Machines Throttle Valve (Intake Air) - Remove and Install - Side Facing Inlet Elbow
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Install
C3.4B Engines for Caterpillar Built Machines Electronic Unit Injector - Remove
C3.4B Engines for Caterpillar Built Machines Electronic Unit Injector - Install
C3.4B Engines for Caterpillar Built Machines Turbocharger - Remove - Top Mounted Turbocharger
C3.4B Engines for Caterpillar Built Machines Turbocharger - Remove - Side Mounted Turbochargers
C3.4B Engines for Caterpillar Built Machines Turbocharger - Install - Side Mounted Turbocharger
C3.4B Engines for Caterpillar Built Machines Turbocharger - Install - Top Mounted Turbocharger
C3.4B Engines for Caterpillar Built Machines Wastegate Solenoid - Remove and Install