Fuel Manifold (Rail) - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 388-1289 | 封盖套件 | 1 |
开始:
- 拆下燃油喷油管。 有关正确的步骤,请参阅拆解和组装, "燃油喷油管 - 拆卸"。
Show/hide table
接触高压燃油可能导致液体渗透和烧伤危险。 高压燃油溢出可能会产生火灾。 如果不遵循检查、保养和维修指南,可能会造成人身伤亡。 |
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅系统运作,测试和调整, "燃油系统部件清洁度"。 |
注: 用新的塞子或盖塞住或盖住所有打开的端口。
- 彻底清洁燃油歧管 (12) 周围的区域。
Show/hide table
图 1 g03784524 Show/hide table图 2 g03784525 - 从燃油压力传感器 (3) 上断开导线线束。
- 将软管组件接头 (9) 从喷油泵 (8) 上断开。
- 将软管组件接头 (6) 从配油盘 (5) 上断开。
- 将螺栓 (1) 从燃油歧管 (2) 上拆下。 将燃油歧管从气门机构盖 (4) 上拆下。
- 如有必要,遵循步骤 6.a 至 6.e 以便拆下塑料管组件 (7)。
- 释放塑料管组件 (7) 上的软管卡箍 (10)。
- 将塑料管组件 (7) 从燃油歧管 (2) 上断开。
- 使用工具 (A) 用一个新的盖盖住燃油歧管 (2) 打开的端口。
- 拆下密封件 (11)。
- 使用工具 (A) 用一个新的塞塞住塑料管组件 (7) 的开口端。
- 如有必要,将燃油压力安全阀 (12) 和 O 形密封圈 (13)(未显示)从燃油歧管上拆下。
- 如有必要,从燃油歧管上拆下燃油压力传感器 (3)。
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅系统运作,测试和调整, "燃油系统部件清洁度"。 |
- 确保盖住燃油歧管上所有端口。 确保燃油歧管外部清洁且无损坏。
注: 请勿安装没有塞住的燃油歧管。 必须将所有塞和盖保留到位,直到即将安装喷油管前。
Show/hide table图 3 g03784524 Show/hide table图 4 g03784525 - 如有必要,将燃油压力安全阀 (12) 和新 O 形密封圈 (13)(未显示)安装到燃油歧管 (2) 上。 拧紧燃油压力安全阀 (12) 至扭矩为
100 N·m (74 lb ft) 。 - 如有必要,将燃油压力传感器 (3) 安装到燃油歧管上。 将燃油压力传感器 (3) 拧紧至扭矩为
70 N·m (52 lb ft) 。 - 如有必要,遵循步骤 4.a 至 4.d 以便将管组件 (7) 安装到燃油歧管 (2) 上。
- 将软管卡箍 (10) 定位到塑料管组件 (7) 上。
- 将新的密封件 (11) 安装到塑料管组件 (7) 中。
- 将塑料管组件 (7) 安装到燃油歧管 (2) 上。
注: 确保塑料管组件朝向正确。
- 牢固地拧紧软管卡箍 (10)。
- 将燃油歧管 (2) 定位到气门机构盖 (4) 上。 将螺栓 (1) 安装到燃油歧管 (2) 上,用手拧紧。
- 安装新的喷油管,并用手拧紧。 有关安装步骤,请参阅拆解和装配, "喷油管 - 安装"。
注: 在组装步骤的这一阶段,不要紧固喷油管螺母。
- 拧紧螺栓 (1) 至扭矩为
25 N·m (221 lb in) 。 - 拧紧喷油管螺母。 有关正确的步骤,请参阅拆解和装配, "喷油管 - 安装"。
- 从接头 (9) 上拆下螺塞,并将塑料管组件 (7) 安装到喷油泵 (8) 上。
- 从接头 (6) 上拆下螺塞,并将塑料管组件 (7) 安装到配油盘 (5) 上。
- 有关喷油管的其余安装步骤,请参阅拆解和装配, "喷油管 - 安装"。
结束:
- 如果安装新的燃油歧管,将需要使用电子维修工具来执行"油轨压力值学习复位"步骤。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Water Separator and Fuel Filter (Primary) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C3.4B Engines for Caterpillar Built Machines Flow Control Valve - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490} Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490}
Procedure for Seismic Anchor Installation of Multi Module Systems{4480} Procedure for Seismic Anchor Installation of Multi Module Systems{4480}
XQC1200 and XQC1600 Power Modules Exhaust Elbow - Remove and Install
455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000}
C27 and C32 Generator Set Engines Electronic Control Module - Remove and Install
C27 and C32 Generator Set Engines Turbocharger Outlet Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Fuel Temperature Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Injection Lines - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Lines - Install
C3.4B Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Throttle Valve (Intake Air) - Remove and Install - Rear Facing Inlet Elbow
C3.4B Engines for Caterpillar Built Machines Throttle Valve (Intake Air) - Remove and Install - Side Facing Inlet Elbow
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Install
C3.4B Engines for Caterpillar Built Machines Electronic Unit Injector - Remove
C3.4B Engines for Caterpillar Built Machines Electronic Unit Injector - Install
C3.4B Engines for Caterpillar Built Machines Turbocharger - Remove - Top Mounted Turbocharger