Turbocharger Outlet Pressure Sensor - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 断开线束组件 (2) 。
Show/hide table
图 1 | g03686067 |
- 从进气歧管上拆下涡轮增压器出口压力传感器 (1) 。
- 将 O 形密封圈(未显示)从涡轮增压器出口压力传感器 (2) 上拆下。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将一个新的 O 形密封圈(未显示)安装到涡轮增压器出口压力传感器 (1) 上。
Show/hide table
图 2 | g03686067 |
- 安装涡轮增压器出口压力传感器 (1) 并拧紧至扭矩为 10 ± 2 N·m (90 ± 18 lb in)。
- 连接线束组件 (2) 。
Caterpillar Information System:
C27 and C32 Generator Set Engines Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Fuel Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Fuel Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Engine Oil Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Coolant Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Crankshaft Position Sensor - Remove and Install
C27 and C32 Generator Set Engines Camshaft Position Sensor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
C27 and C32 Generator Set Engines Atmospheric Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Turbocharger - Assemble
Procedure for Installing the Continuous Engine Prelube Oil Pump Group and Lines Group for Certain 3508 Fire Pump Engines{1307, 1319} Procedure for Installing the Continuous Engine Prelube Oil Pump Group and Lines Group for Certain 3508 Fire Pump Engines{1307, 1319}
The Check Ball in the Spool Assembly of the Main Relief Valve May be Missing on Various Products{3133, 3182, 3210, 3213} The Check Ball in the Spool Assembly of the Main Relief Valve May be Missing on Various Products{3133, 3182, 3210, 3213}
C27 and C32 Generator Set Engines Electronic Control Module - Remove and Install
455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000}
XQC1200 and XQC1600 Power Modules Exhaust Elbow - Remove and Install
Procedure for Seismic Anchor Installation of Multi Module Systems{4480} Procedure for Seismic Anchor Installation of Multi Module Systems{4480}
Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490} Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490}
C3.4B Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
C3.4B Engines for Caterpillar Built Machines Flow Control Valve - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C3.4B Engines for Caterpillar Built Machines Water Separator and Fuel Filter (Primary) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Injection Lines - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Lines - Install