Fuel Priming Pump - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 388-1289 | 封盖套件 | 1 |
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅系统运作,测试和调整, "燃油系统部件清洁度"。 |
Show/hide table
注意 |
---|
在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。 按照本地法规和要求处置所有油液。 |
- 将燃油供应转到断开位置。
Show/hide table
图 1 g02988817 典型示例 - 在塑料管组件 (1) 上作临时识别标记,以显示管组件的正确位置。
- 将适当的容器放置到燃油注油泵的下方,用来盛装所有可能洒出的燃油。 排放粗滤器 (7)。 参阅操作和保养手册, "燃油系统粗滤器(油水分离器)滤芯 - 更换"。
- 断开塑料管组件 (1)。 使用工具 (A) 用新的塞塞住管组件。
- 使用工具 (A) 用新的盖盖住燃油注油泵上打开的接头 (2)。
- 将粗滤器 (6) 从燃油注油泵 (4) 上拆下。 请参阅操作和保养手册, "燃油系统粗滤器(油水分离器)滤芯 - 更换"。
- 将螺栓 (7) 从燃油注油泵 (4) 拆下。 将燃油注油泵 (4) 从安装支架上拆下。
- 如有必要,按照步骤 8.a 至 8.d 拆解燃油注油泵 (4)。
- 将接头 (2) 从燃油注油泵 (4) 拆下。 用工具 (A) 塞住燃油注油泵 (4)。
- 使用工具 (A) 盖住接头 (2)。
- 将螺塞 (5) 从燃油注油泵 (4) 拆下。 用工具 (A) 塞住燃油注油泵 (4)。
- 将 O 形密封圈 (3) 从接头 (2) 和螺塞 (5) 上拆下。
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅系统运作,测试和调整, "燃油系统部件清洁度"。 |
- 确保燃油注油泵 (4) 清洁且无磨损或损坏。 如有必要,更换燃油注油泵。
Show/hide table
图 2 g02988817 典型示例 - 如有必要,按照步骤 2.a 至 2.f,组装燃油注油泵 (4)。
- 将新的 O 形密封圈 (3) 安装到螺塞 (5) 上。
- 从接头 (2) 上拆下盖。 将新的 O 形密封圈 (3) 安装到接头 (2) 上。
- 将螺塞从燃油注油泵 (4) 上拆下。
- 将接头 (2) 安装到燃油注油泵 (4) 上。
- 将螺塞 (5) 安装到燃油注油泵 (4) 上。
- 拧紧螺塞和接头至扭矩为
20 N·m (14 lb ft) 。
- 将燃油注油泵 (4) 安置到安装支架上。 将螺栓 (7) 安装到燃油注油泵上。 拧紧螺栓至扭矩为
44 N·m (32 lb ft) 。 - 将螺塞从所有塑料管组件上拆下。 将盖子从接头上拆下。
- 将塑料管组件 (1) 连接到接头 (2) 上。
注: 确保塑料管组件安装在原来的位置上。
- 将新的粗滤器 (6) 安装到燃油注油泵 (4) 上。 参阅操作和保养手册, "燃油系统粗滤器(油水分离器)滤芯 - 更换"。
- 将燃油供应转到接通位置。
- 充注燃油系统。 请参阅操作和保养手册, "燃油系统 - 充油"。
Caterpillar Information System:
Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490} Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490}
Procedure for Seismic Anchor Installation of Multi Module Systems{4480} Procedure for Seismic Anchor Installation of Multi Module Systems{4480}
XQC1200 and XQC1600 Power Modules Exhaust Elbow - Remove and Install
455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000}
C27 and C32 Generator Set Engines Electronic Control Module - Remove and Install
C27 and C32 Generator Set Engines Turbocharger Outlet Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Fuel Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Fuel Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Engine Oil Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Coolant Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Crankshaft Position Sensor - Remove and Install
C3.4B Engines for Caterpillar Built Machines Flow Control Valve - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C3.4B Engines for Caterpillar Built Machines Water Separator and Fuel Filter (Primary) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Manifold (Rail) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Fuel Injection Lines - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Lines - Install
C3.4B Engines for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Throttle Valve (Intake Air) - Remove and Install - Rear Facing Inlet Elbow
C3.4B Engines for Caterpillar Built Machines Throttle Valve (Intake Air) - Remove and Install - Side Facing Inlet Elbow
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump - Remove
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump - Install
C3.4B Engines for Caterpillar Built Machines Fuel Injection Pump Gear - Remove