Camshaft Position Sensor - Remove and Install
拆卸步骤
Show/hide table
| 注意 |
|---|
在进行检验、保养、测试、调整及维修产品期间，必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前，要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品，请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 断开线束组件 (1) 。
Show/hide table
 | |
| 图 1 | g03685940 |
- 拆下螺栓 (3) 和凸轮轴位置传感器 (2) 。
- 将 O 形密封圈（未显示）从凸轮轴位置传感器 (3) 上拆下。
安装步骤
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在凸轮轴位置传感器（未显示）上安装一个新的 O 形密封圈。 用清洁的发动机机油润滑 O 形密封圈。
Show/hide table
| | |
| 图 2 | g03685940 |
- 把凸轮轴位置传感器 (2) 定位到前壳体中并安装螺栓 (3) 。 将螺栓 (3) 拧紧至扭矩为 28 ± 7 N·m (21 ± 5 lb ft)。
- 连接线束组件 (1) 。
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
C27 and C32 Generator Set Engines Atmospheric Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Turbocharger - Assemble
Procedure for Installing the Continuous Engine Prelube Oil Pump Group and Lines Group for Certain 3508 Fire Pump Engines{1307, 1319} Procedure for Installing the Continuous Engine Prelube Oil Pump Group and Lines Group for Certain 3508 Fire Pump Engines{1307, 1319}
The Check Ball in the Spool Assembly of the Main Relief Valve May be Missing on Various Products{3133, 3182, 3210, 3213} The Check Ball in the Spool Assembly of the Main Relief Valve May be Missing on Various Products{3133, 3182, 3210, 3213}
C4.4 Engines for Caterpillar Built Machines Crankshaft Timing Ring - Remove and Install
Customer Assembly Requirements for C3.4B Engine {1000, 108D} Customer Assembly Requirements for C3.4B Engine {1000, 108D}
455-1188 Major Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1188 Major Overhaul Foundational Kit for C18 Marine Engines{1000}
G3306B Petroleum Generator Set Engines Electrical Connectors
C27 and C32 Generator Set Engines Turbocharger - Disassemble
C27 and C32 Generator Set Engines Fuel Filter Base - Install
C27 and C32 Generator Set Engines Fuel Filter Base - Remove
C27 and C32 Generator Set Engines Crankshaft Position Sensor - Remove and Install
C27 and C32 Generator Set Engines Coolant Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Engine Oil Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Fuel Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Fuel Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Inlet Air Temperature Sensor - Remove and Install
C27 and C32 Generator Set Engines Turbocharger Outlet Pressure Sensor - Remove and Install
C27 and C32 Generator Set Engines Electronic Control Module - Remove and Install
455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000} 455-1194 Top End Overhaul Foundational Kit for C18 Marine Engines{1000}
XQC1200 and XQC1600 Power Modules Exhaust Elbow - Remove and Install
Procedure for Seismic Anchor Installation of Multi Module Systems{4480} Procedure for Seismic Anchor Installation of Multi Module Systems{4480}
Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490} Installation Guide for the Tire Monitoring System on Cat® and Non-Cat Equipment {4203, 7490}