Accessory Drive - Remove and Install - Accessory Drive SAE "B"
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 8H-0663 | 轴承拉拔器 | 1 |
5F-7345 | 拉拔器 | 1 | |
126-7183 | 十字挡块 | 1 | |
126-7177 | 拉拔器腿 | 2 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 将辅助设备从附件驱动器壳体上拆下。 有关正确步骤,请参阅原始设备制造商(OEM)信息。
Show/hide table
图 1 g03360850 - 如果 OEM 从动设备未安装到辅助驱动上,则拆下螺栓 (1)。 拆下盖板 (2),然后拆下 O 形密封圈 (3)(未显示)。
Show/hide table
图 2 g03431636 - 将卡环 (9) 从壳体 (4) 上拆下。
- 将齿轮组件 (6) 从壳体 (4) 上拆下。
- 必要时,遵循步骤 5.a 至 5.c 拆解齿轮组件 (6)。
- 将卡环 (8) 从齿轮组件 (6) 上拆下。
- 使用工具 (A) 将轴承 (7) 从齿轮 (6) 上拆下。
- 使用适当的工具将轴承 (5) 从壳体 (4) 上拆下。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | 7M-7456 | 轴承安装固定胶 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 3 | g03431639 |
- 在轴承 (5) 的外表面 (X) 处涂敷一薄层连续的工具 (B)。
- 使用适当的工具将轴承 (5) 安装到壳体 (4) 上。 清除过多的轴承安装固定胶。
Show/hide table
图 4 g03431658 Show/hide table图 5 g03431659 - 必要时,遵循步骤 3.a 至步骤 3.g 将轴承 (7) 组装到齿轮 (6) 上。
- 检查齿轮 (6) 的轮齿和花键有无磨损或损坏。 检查轴承 (7)、卡环 (8) 和卡环 (9)。
- 检查壳体 (4) 中的孔有无损坏。 如有必要,更换前壳体。 有关正确的步骤,请参阅拆解和组装, "壳体(前)- 拆卸"和拆解和组装, "壳体(前)- 安装"。
- 在轴承 (7) 的内表面 (Y) 处涂敷一薄层连续的工具 (B)。 将轴承 (7) 的内座圈放置在适当的支架上。 将齿轮 (6) 的轴按入轴承 (7) 中,使齿轮的肩抵到轴承上。 清除过多的轴承安装固定胶。
- 将卡环 (8) 安装到齿轮 (6) 的凹槽中。
- 在轴承 (7) 的外表面 (Z) 处涂敷一薄层连续的工具 (B)。
- 将齿轮组件 (6) 安装到壳体 (4) 上。 确保齿轮 (6) 的轴与壳体 (4) 中的轴承正确对齐。 清除过多的轴承安装固定胶。
- 将卡环 (9) 安装到附件驱动器壳体 (4) 的凹槽中。 确保卡环 (9) 在凹槽中的位置正确。
- 确保惰齿轮与附件驱动器齿轮之间存在能感觉到的齿隙。
Show/hide table
图 6 g03360850 - 将辅助设备安装到附件驱动器壳体上。 有关正确的步骤,请参阅 OEM 信息。
- 如果 OEM 从动设备不会安装到辅助驱动上。 安装新的 O 形密封圈 (3)(未显示)和盖板 (2) 。 安装螺栓 (1) 并拧紧螺栓至扭矩为
44 N·m (33 lb ft) 。
Caterpillar Information System:
793F and 797F Off-Highway Trucks Braking System Parking Brake Accumulator Is Frequently Charging
793F and 797F Off-Highway Trucks Braking System Service Brake Pressure Is Low
793F and 797F Off-Highway Trucks Braking System Service Brake Pressure Is High
793F and 797F Off-Highway Trucks Braking System Service Brake Accumulator Is Frequently Charging
793F and 797F Off-Highway Trucks Braking System Brake System
UPS 750 Uninterruptible Power Supply Additional UPS Concepts
C4.4 Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install - Engines With an Automatic Belt Tensioner
C4.4 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C4.4 Engines for Caterpillar Built Machines Flywheel - Install
C4.4 Engines for Caterpillar Built Machines Flywheel - Remove
C4.4 Engines for Caterpillar Built Machines Water Temperature Regulator - Remove and Install
C4.4 Engines for Caterpillar Built Machines Water Pump - Install
C4.4 Engines for Caterpillar Built Machines Accessory Drive - Remove and Install - Accessory Drive SAE "A"
793F and 797F Off-Highway Trucks Braking System Parking Brake Pressure Is High
Cat® Digital Voltage Regulator Electrical
XQC1200 and XQC1600 Power Modules Air Cleaner - Remove and Install
Fuel Pressure Gauge Reads Incorrect Suspect Parameter Number (SPN) {7451, 7456} Fuel Pressure Gauge Reads Incorrect Suspect Parameter Number (SPN) {7451, 7456}
Cat® Digital Voltage Regulator Dimensions
3516C and C175-16 Engines Selective Catalytic Reduction SCR Catalyst Sulfation Is Excessive
Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.4 {4490} Procedure to Upgrade EMCP 1, EMCP 2, EMCP 2+, EMCP 3.1, EMCP 3.2, and EMCP 3.3 to EMCP 4.4 {4490}
793F and 797F Off-Highway Trucks Braking System Parking Brake Pressure Is Low
793F and 797F Off-Highway Trucks Braking System Hoist Pilot Pressure Is High
793F and 797F Off-Highway Trucks Braking System Hoist Pilot Pressure Is Low
793F and 797F Off-Highway Trucks Braking System Service Brake Cooling Temperature Is High