Swing Gear and Bearing
Show/hide table
Illustration 1 | g03819005 |
Top view |
Show/hide table
Item | Qty | Part | Specification Description |
---|---|---|---|
1 | - | - | Position “S” that is on inner race (7) relative to the carbody assembly (1) and bearing stopper (2). Refer to Illustration 1. |
2 | - | - | |
3 | 16 | 8T-4136 Bolt | Before assembly, apply blue Loctite 243 to the threads.
Torque to |
Show/hide table
Illustration 2 | g03819006 |
Show/hide table
Item | Qty | Part | Specification Description |
4 | 4 | 8T-4139 Bolt | Before assembly, apply blue Loctite 243 to the threads. |
5 | 1 | 7Y-1095 Dowel | Apply Loctite C5A Copper Anti-Seize to the dowel holes. |
6 | 4 | 8T-4136 Bolt | Before assembly, apply blue Loctite 243 to the threads.
Torque to |
8 | 74 | 532-0243 Bolt | Before assembly, remove compound, oil, and dust from female threads, then apply Loctite C5A Copper anti-seize compound to the threads.
Use the following tightening procedure: 1. Tighten bolts to 2. Turn to an additional angle of 90 ± 5 degrees. |
9 | - | - | Before assembly, apply 8C-8422 Sealant between the mating surfaces of the gear group and upper frame assembly. Apply sealant between the mating surfaces of the gear group and carbody assembly. |
10 | 48 | 461-3894 Bolt | Before assembly, remove compound, oil, and dust from female threads, then apply Loctite C5A Copper anti-seize compound to the threads.
Use the following tightening procedure: 1. Tighten bolts to 2. Turn to an additional angle of 70 ± 5 degrees. |
Caterpillar Information System:
C13, C15, and C18 Tier 4 Final Engines Variable Valve Actuator
390F Excavator Machine System Swing Drive Mounting
3512C HD and 3516C HD IPP Rental Power Modules Speed Control - Test
C15 Industrial Engines Maintenance Interval Schedule - Engines Which Have Deep Sumps
C15 Industrial Engines Maintenance Interval Schedule - Engines Which Have Shallow Sumps
390F Excavator Machine Systems Pilot Valve (Travel) - Remove and Install
G3306B Generator Sets Alarms and Shutoffs
390F Excavator Machine Systems Pump Drive Coupling - Remove and Install
C4.4 Marine Generator Set Voltage Regulators - R438 Automatic Voltage Regulation AVR
C4.4 Marine Generator Set Control Panel Mounting
C13, C15, and C18 Tier 4 Final Engines Exhaust Manifold
374F Excavator Machine System Control Valve
390F MHPU Mobile Hydraulic Power Unit Machine System Specifications Motor Lines (Reversing Fan)
C13, C15, and C18 Tier 4 Final Engines Variable Valve Actuator Oil Diverter Valve
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing
C9.3 Tier 4 Final Engines Crankshaft Seals
C13, C15, and C18 Tier 4 Final Engines Engine Support (Front)
390F MHPU Mobile Hydraulic Power Unit Machine System Specifications Cooling Lines
C15 and C18 Engines for Caterpillar Built Machines Valve Rocker Arm
C13, C15, and C18 Tier 4 Final Engines Air Compressor
C13 Tier 4 Final Engines Temperature Sensor (Catalyst Inlet)
C9.3 Tier 4 Final Engines Turbocharger
390F Excavator Machine Systems Pilot Valve (Travel) - Disassemble
390F Excavator Machine Systems Pilot Valve (Travel) - Assemble