Pilot Valve (Travel) - Assemble
组装步骤
- 安装螺塞 (39) 。 将螺塞 (39) 拧紧至扭矩为 7 ± 1 N·m (62 ± 9 lb in)。
Show/hide table
图 1 | g02119197 |
- 安装衬套 (38) 、钢球 (37) 、阀座 (36) 、O 形密封圈 (35) 和螺塞 (34) 。 将螺塞 (34) 拧紧至扭矩为 12 ± 1 N·m (106 ± 9 lb in)。
- 将垫圈 (32) 、垫圈 (31) 、弹簧 (30) 和阀座 (29) 安装到滑阀 (33) 上。 将滑阀 (33) 的一端放在阀座 (29) 的槽形开口中。
Show/hide table
图 2 | g02119196 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 安装弹簧 (27) 和滑阀组件 (25) 。
Show/hide table
图 3 | g02119195 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 安装 O 形密封圈 (28) 、O 形密封圈 (26) 、阀组件 (24) 和螺栓 (23) 。 拧紧螺栓 (23) 至扭矩为 9 ± 1 N·m (80 ± 9 lb in)。
- 安装钢球 (22) 、阀座 (21) 、外弹簧 (20) 和内弹簧 (19) 。
Show/hide table
图 4 | g02118913 |
- 将密封件 (16) 安装到螺塞 (14) 上。
Show/hide table
图 5 | g02118900 |
- 将盖 (13) 和 O 形密封圈 (15) 安装到螺塞 (14) 上。
- 将推杆 (17) 安装到螺塞 (14) 上。
- 将活塞 (18) 安装到推杆 (17) 上。
- 安装螺塞组件 (12) 。
Show/hide table
图 6 | g02118899 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 安装盖 (11) 和螺栓 (10) 。 拧紧螺栓 (10) 至 29 ± 3 N·m (21 ± 2 lb ft) 的扭矩。
- 将衬套 (9) 安装到盖 (8) 中。
Show/hide table
图 7 | g02118898 |
- 安装盖 (8) 和螺栓 (7) 。 拧紧螺栓 (7) 至扭矩为 55 ± 10 N·m (41 ± 7 lb ft)。
Show/hide table
图 8 | g02118897 |
- 将调整螺钉 (5) 和螺母 (6) 安装到踏板 (3) 中。
Show/hide table
图 9 | g02118896 |
注: 此时不要拧紧螺母 (6) 。
- 安装踏板 (3) 、凸轮轴 (4) 和调整螺钉 (2) 。 拧紧调整螺钉 (6) 至扭矩为 7 ± 1 N·m (62 ± 9 lb in)。
Show/hide table
图 10 | g02118895 |
- 调整调整螺钉 (5) 以设置尺寸 (X) 。 尺寸 (X) 为 12.4°。
Show/hide table
图 11 | g02119958 |
- 拧紧螺母 (6) 至扭矩为 33 ± 3 N·m (25 ± 3 lb ft)。
End By: 安装先导阀。
Caterpillar Information System:
390F Excavator Machine Systems Pilot Valve (Travel) - Disassemble
C9.3 Tier 4 Final Engines Turbocharger
C13 Tier 4 Final Engines Temperature Sensor (Catalyst Inlet)
C13, C15, and C18 Tier 4 Final Engines Air Compressor
C15 and C18 Engines for Caterpillar Built Machines Valve Rocker Arm
390F MHPU Mobile Hydraulic Power Unit Machine System Specifications Cooling Lines
C13, C15, and C18 Tier 4 Final Engines Engine Support (Front)
C9.3 Tier 4 Final Engines Crankshaft Seals
C15 and C18 Engines for Caterpillar Built Machines Flywheel Housing
C13, C15, and C18 Tier 4 Final Engines Variable Valve Actuator Oil Diverter Valve
390F MHPU Mobile Hydraulic Power Unit Machine System Specifications Motor Lines (Reversing Fan)
390F MHPU Mobile Hydraulic Power Unit Machine System Specifications Swing Gear and Bearing
C9.3 Tier 4 Final Engines Engine Oil Pan
C9.3 Tier 4 Final Engines Diesel Particulate Filter
TH55FT-E70 and TH55FT-E90 Transmissions Maintenance Interval Schedule
374F Excavator Machine System Gear Pump
C9.3 Tier 4 Final Engines Camshaft
390F MHPU Mobile Hydraulic Power Unit Machine System Specifications Relief Valve (Pilot)
3512C Marine Auxiliary Generator Set Engines with Dynamic Gas Blending Fuel Temperature Is Low
390F MHPU Mobile Hydraulic Power Unit Machine System Specifications Relief Valve (Pilot)
390F Excavator Machine Systems Cab - Remove and Install
3512C HD and 3516C HD IPP Rental Power Modules Sensor Supply - Test
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Maintenance Interval Schedule
797 Off-Highway Truck Powered Stairway - Check