Centershift Lock Bar and Bushings - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1U-9200 | Lever Puller Hoist | 1 |
| C | 1P-1832 | Adapter | 1 |
| 5P-4776 | Tool Stud | 1 | |
| 9U-6833 | Nut | 1 | |
| 5P-8250 | Washer | 1 | |
| 6V-3160 | Double Acting Cylinder | 1 | |
| 3S-6224 | Electric Hydraulic Pump Gp | 1 | |
| 5F-7693 | Spacer As | 1 | |
| D | 1P-0510 | Driver Gp | 1 |
| E | 1P-1836 | Bearing Puller Adapter | 1 |
| 1U-7758 | Stud | 1 | |
| 9U-6832 | Nut | 1 | |
| 4K-0684 | Hard Washer | 1 | |
| 6V-3170 | Double Acting Cylinder | 1 | |
| 350-7768 | Electric Hydraulic Pump Gp (115V) | 1 | |
| 350-7769 | Electric Hydraulic Pump Gp (230V) | 1 | |
| 5P-4197 | Spacer | 1 | |
| F | 123-3804 | Bearing Puller Adapter | 1 |
| 1U-7758 | Stud | 1 | |
| 9U-6832 | Nut | 1 | |
| 4K-0684 | Hard Washer | 1 | |
| 6V-3170 | Double Acting Cylinder | 1 | |
| 350-7768 | Electric Hydraulic Pump Gp (115V) | 1 | |
| 350-7769 | Electric Hydraulic Pump Gp (230V) | 1 | |
Show/hide table
 |
|
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death. |
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.
- Use Tooling (D) in order to install seals (11).
Show/hide table
Illustration 2 g01397706 Show/hide table
Illustration 3 g01397714 - Use Tooling (F) in order to install bearing (12).
- Use Tooling (E) in order to install bushings (13).
Show/hide table
Illustration 4 g01397600 - Attach a suitable lifting device to centershift lock bar (8).
- Position centershift lock bar (8) to the original location and install pin (10).
Show/hide table
Illustration 5 g01397593 - Attach a suitable lifting device to opposite side of centershift lock bar (8).
- Position centershift lock bar (8) and install pin (7).
- Install lock (9) and bolts (6).
Show/hide table
Illustration 6 g01397553 - Attach a suitable lifting device to centershift cylinder (2).
- Position centershift cylinder (2). Use the machine in order to position the cylinder rod.
- Install cap (4) and bolts (3).
Show/hide table
Illustration 7 g01397540 - Remove Tooling (A) and a suitable lifting device from blade lift arms (1).
Show/hide table
| |
| Illustration 1 | g01397601 |
End By:
- Separate the steering frame lock.
Caterpillar Information System:
Bench Test Procedure for a CX31 On Highway Truck or AD22 Articulated Truck Transmission {3030, 3073} Bench Test Procedure for a CX31 On Highway Truck or AD22 Articulated Truck Transmission {3030, 3073}
Disassembly and Assembly Procedure for 3N-8891 Sea Water Heat Exchanger Gp {1379} Disassembly and Assembly Procedure for 3N-8891 Sea Water Heat Exchanger Gp {1379}
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines
C18 Petroleum Engine Maintenance Interval Schedule
C4.4 Industrial Engine Belt - Inspect
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines
C4.4 Industrial Engine Belt Tensioner - Check
2013/10/21 Recommendations For Parameters and Update Rates On PL1000T For Certain C32, 3500, and G3500 Engines {1926}
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Electrical Connections
C13 and C15 Generator Sets Safety Messages
320D2 Excavator Machine Electronic Control System Diagnostic Capabilities
308E2 CR Mini Hydraulic Excavator Final Drive Oil Sample - Obtain
C18 Petroleum Engine Product Description
CX31-P600 Petroleum Transmission Maintenance Interval Schedule
14L Motor Grader Machine Systems Centershift Lock Bar and Bushings - Remove
C18 Petroleum Engine Gauges and Indicators
C18 Petroleum Engine Monitoring System
Retrofit SCR Aftertreatment Catalyst (SCR) - Replace
EMCP4.1/EMCP4.2 Integrated Voltage Regulator
Retrofit Diesel Particulate Filter (DPF) Systems Glossary
Retrofit SCR Aftertreatment Diesel Particulate Filter - Clean/Inspect
Retrofit SCR Aftertreatment Exhaust Inlet Nitrogen Oxide Sensor - Inspect/Replace
Retrofit SCR Aftertreatment Exhaust Outlet Nitrogen Oxide Sensor - Inspect/Replace
Retrofit SCR Aftertreatment Catalyst (DOC) - Replace