Air Inlet and Exhaust Lines
Show/hide table
| |
| Illustration 1 | g03484818 |
|
Rear view | |
Show/hide table
| |
| Illustration 2 | g03484821 |
|
Bolt tightening sequence | |
Show/hide table
| Specification for 419-5447 Air Lines Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 8 | 6V-3917 O-Ring Seal | Before assembly, lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
| 2 | 4 | 3J-5389 Plug | Before assembly, apply Loctite C5A Copper Anti-Seize to the threads.
Torque to |
| 3 | 8 | 6V-1943 High Temperature Bolt | Before assembly, apply Loctite C5A Copper Anti-Seize to the threads and bearing surfaces.
Torque to |
| 3 | 10 | 9F-2773 Bolt | Use the following procedure in order to assemble the aftercooler assembly and tighten the bolts:
1. Assemble the seals to the aftercooler core. 2. Temporarily secure the bottom seal to the aftercooler with tape. Do not use an adhesive, a silicone lubricant, or any other lubricant for retention of the seal. 3. Assemble the aftercooler with seals to the inlet manifold. 4. Inspect the bottom seal in order to ensure that the seal is seating correctly in the recess. 5. Install the aftercooler cover. 6. Inspect the upper seal in order to ensure that the seal is seating correctly in the recess. 7. Install the cover bolts. Hand tighten the cover bolts. 8. Tighten the bolts in a numerical sequence that is shown in Illustration 2 to 9. Again, tighten the bolts in a numerical sequence that is shown in Illustration 2 to 10. Remove the tape. |
| 5 | 12 | 6V-5101 O-Ring Seal | Before assembly, lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
Caterpillar Information System:
C4.4 Industrial Engine Belt Tensioner - Check
2013/10/21 Recommendations For Parameters and Update Rates On PL1000T For Certain C32, 3500, and G3500 Engines {1926}
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies Electrical Connections
C13 and C15 Generator Sets Safety Messages
320D2 Excavator Machine Electronic Control System Diagnostic Capabilities
308E2 CR Mini Hydraulic Excavator Final Drive Oil Sample - Obtain
308E2 CR Mini Hydraulic Excavator Final Drive Oil Level - Check
308E2 CR Mini Hydraulic Excavator Final Drive Oil - Change
2013/12/05 New Engine Software Is Used On Certain 3516C Engines {1920}
C13 and C15 Generator Sets Model View Illustrations
320D2 Excavator Machine Electronic Control System Connector Locations
320D2 Excavator Machine Electronic Control System Service Tools
C4.4 Industrial Engine Belt - Inspect
C18 Petroleum Engine Maintenance Interval Schedule
3512B and 3516B Generator Set Engines with Dynamic Gas Blending Air Inlet and Exhaust Lines
Disassembly and Assembly Procedure for 3N-8891 Sea Water Heat Exchanger Gp {1379} Disassembly and Assembly Procedure for 3N-8891 Sea Water Heat Exchanger Gp {1379}
Bench Test Procedure for a CX31 On Highway Truck or AD22 Articulated Truck Transmission {3030, 3073} Bench Test Procedure for a CX31 On Highway Truck or AD22 Articulated Truck Transmission {3030, 3073}
14L Motor Grader Machine Systems Centershift Lock Bar and Bushings - Install
C18 Petroleum Engine Product Description
CX31-P600 Petroleum Transmission Maintenance Interval Schedule
14L Motor Grader Machine Systems Centershift Lock Bar and Bushings - Remove
C18 Petroleum Engine Gauges and Indicators
C18 Petroleum Engine Monitoring System
Retrofit SCR Aftertreatment Catalyst (SCR) - Replace