Flywheel Housing - Remove and Install - Standard Housing
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 M10 × 100 mm |
2 |
开始:
- 拆下飞轮。 有关正确的步骤,请参阅拆解和组装, "飞轮 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将螺栓 (3) 从飞轮壳体 (1) 的位置 (X) 上拆下。
- 将工具 (A) 安装在飞轮壳体 (1) 上的位置 (X)。
- 将适当的起吊设备安装到飞轮壳体上来支撑住飞轮壳体。 飞轮壳体的重量约为
40 kg (88 lb) 。 - 将螺栓 (2) 和其余螺栓 (3) 从飞轮壳体 (1) 上拆下。
- 使用适当的起吊设备,将飞轮壳体 (1) 从缸体上卸下。
Show/hide table
图 3 g01983533 典型实例 - 拆下防尘密封件 (5)。
- 如有必要,将定位销 (4) 从缸体上卸下。
Show/hide table
图 1 | g02227473 |
典型实例 |
Show/hide table
图 2 | g02227474 |
典型实例 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 M10 × 100 mm |
2 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保飞轮壳体清洁且无损坏。 如有必要,更换飞轮壳体。
Show/hide table
图 4 g01983535 典型实例 - 检查曲轴后油封 (6) 有无泄漏。 如果观察到漏油,更换曲轴后油封。 有关正确的步骤,请参阅拆解和组装, "曲轴后油封 - 拆卸"和拆解和组装, "曲轴后油封 - 安装"。
- 清洁缸体后表面。 如有必要,将定位销 (4) 安装到缸体上。
- 将工具 (A) 安装到缸体上。
- 安装防尘密封件 (5)。
Show/hide table
图 5 g02227475 典型实例 - 将适当的起吊设备安装到飞轮壳体上。 飞轮壳体的重量约为
40 kg (88 lb) 。 - 使用起吊设备对准飞轮壳体 (1) 与工具 (A)。 将飞轮壳体安装到缸体上。
- 安装螺栓 (2) 和螺栓 (3)。
- 拆下工具 (A)。 安装其余的螺栓 (3)。
Show/hide table
图 6 g01984554 螺栓级别的识别 - 当安装了 8.8 级别的螺栓时,按照步骤 10.a 至步骤 10.b。
- 拧紧螺栓 (3) 至扭矩为
63 N·m (46 lb ft) 。 - 拧紧螺栓 (2) 至扭矩为
78 N·m (58 lb ft) 。
- 拧紧螺栓 (3) 至扭矩为
- 当安装了 10.9 级别的螺栓时,按照步骤 11.a 至步骤 11.b。
- 拧紧螺栓 (3) 至扭矩为
115 N·m (85 lb ft) 。 - 拧紧螺栓 (2) 至扭矩为
190 N·m (140 lb ft) 。
- 拧紧螺栓 (3) 至扭矩为
- 检查飞轮壳体 (1) 和曲轴的对准。 有关更多信息,请参阅系统操作、测试和调整, "飞轮壳体 - 检查"。
结束:
- 安装飞轮。 有关正确的步骤,请参阅拆解和组装, "飞轮 - 安装"。
Caterpillar Information System:
C4.4 Industrial Engine Refill Capacities
C4.4 Industrial Engine After Stopping Engine
C4.4 Industrial Engine Stopping the Engine
3500 Engines Pistons and Connecting Rods - Remove
C15 and C18 Engines for China On-Highway Phase IV Diagnostic Trouble Codes
C15 and C18 Industrial Engines Product Lifting
C13T-TH35 and C15T-TH35 Petroleum Packages Torque Converter and Transmission Oil - Change
2013/10/28 New Seal Kits Are Available to Service the Flexible Generator Couplings Used on Certain C175-16 Locomotive and Petroleum Engines {3252}
C13T-TH35 and C15T-TH35 Petroleum Packages Maintenance Interval Schedule
C13T-TH35 and C15T-TH35 Petroleum Packages Breather (Transmission Tank) - Clean
C13 Generator Set Engine Fuel Cooler - Remove and Install
C13T-TH35 and C15T-TH35 Petroleum Packages Coolant (ELC) - Change
3500 Engines Pistons and Connecting Rods - Install
2013/11/27 A New Aftercooler Core Assembly Is Used on Certain 797 and 797B Off-Highway Truck Engines {1063}
C15 and C18 Engines for China On-Highway Phase IV Data Link - Test
3600 and C280 Diesel Engine Fluids Recommendations Reference Material
C15 and C18 Engines for China On-Highway Phase IV ARD Combustion Supply Air Pressure Is Low
C15 and C18 Engines for China On-Highway Phase IV ARD Failed to Ignite
3600 and C280 Diesel Engine Fluids Recommendations Coolant Recommendations - General Maintenance
2013/11/13 Special Instructions Are Available for Installing a New Water Lines Clip on G3516B and G3520B Petroleum Engines {1380, 7553}
C15 and C18 Engines for China On-Highway Phase IV ARD Fuel Pressure Is High
C15 and C18 Engines for China On-Highway Phase IV ARD Fuel Pressure Is Low
3600 and C280 Diesel Engine Fluids Recommendations General Coolant Information
C15 and C18 Engines for China On-Highway Phase IV ARD Loss of Combustion