Exhaust Manifold - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 2P-2333 | High Temperature Sealer | - |
B | - | Loctite C5-A Copper Antiseize | - |
Start By:
- Remove the turbocharger.
- Remove locknuts (1) and exhaust manifold assembly (2). Discard locknuts (1).
Show/hide table
Illustration 2 g03418679 - Remove gaskets (4) and studs (3). Discard gaskets (4).
Show/hide table
Illustration 3 g03418681 - Separate manifolds (5) and (7) from manifold (6). Remove studs (8).
Show/hide table
Illustration 1 | g03418678 |
- Install exhaust manifold assembly (2) in the reverse order of removal.
- Apply Tooling (A) to male ends of manifolds (5) and (7).
- Apply Tooling (B) to studs (8) and (3). Tighten studs (8) and (3) to a torque of
35 ± 5 N·m (26 ± 4 lb ft) . The torque tool speed should not exceed 100 RPM. - Install gaskets (4) so that the tabs are down.
Show/hide table
Illustration 4 g01100255 - Apply Tooling (B) to locknuts (3). Tighten locknuts (3) in the above sequence to a torque of
55 ± 5 N·m (41 ± 4 lb ft) .
Caterpillar Information System:
C7.1 Industrial Engine Injector (Diesel Exhaust Fluid) - Replace
349F and 352F Excavators Leaving the Machine
C15 and C18 Engines for China On-Highway Phase IV Diagnostic Capabilities
2013/09/20 A New and Improved Switch and Contactor Are Used for the Jacket Water Heater Control on Certain 3512C Engines {1383, 1408, 1408}
C7.1 Industrial Engine Diesel Exhaust Fluid - Fill
2013/09/16 New Wiring Harness Film Is Used for the Pre-lubrication Pump on Certain G3500 Engines {1319, 1408}
3500 Engines Engine Oil Cooler - Assemble
3500 Engines Engine Oil Cooler - Disassemble
2013/08/15 New Software For Cat® ET Can Now Be Used For All Caterpillar Products {0785, 7606}
2013/08/06 New Engine Oil Filter for C3.4B Engines {1308}
C4.4 Engines Diesel Oxidation Catalyst Has Low Conversion Efficiency
C7.1 Engines Camshaft Position Sensor - Remove and Install
3500 Engines Turbocharger - Remove
3500 Engines Turbocharger - Install
C13 Generator Set Engine Water Pump - Remove and Install
C13 Generator Set Engine Water Temperature Regulator - Remove and Install
2013/12/19 A New Pre-Lube System Is Used On Certain 3508 Industrial Engines Used In Fire Pump Applications {1307, 1319}
2013/11/08 New V Band Clamps and Mounting Hardware Are Used on Certain 3512C Engines {1059, 1071, 7553}
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Solenoid Valves
CAT WDS OEM and 777F Off-Highway Truck/Tractor Water Delivery System Gear Pump (Charge) - Remove and Install
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control
Site Positioning Requirements for Cat® MineStar System Products {7605} Site Positioning Requirements for Cat® MineStar System Products {7605}
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Piston Pump (Water Delivery) - Remove and Install
C4.4 Industrial Engine Emissions Certification Film