Water Temperature Regulator - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 207-1601 | Rubber Lubricant | 1 |
| B | 221-8647 | Seal Installer | - |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.
- Loosen clamps (4) and remove tube assembly (1) .
Show/hide table
 | |
| Illustration 1 | g03418901 |
- Loosen clamp (3) and disconnect hose (2) .
- Remove bolts (5) and temperature regulator housing (6) .
Show/hide table
 | |
| Illustration 2 | g03418902 |
- Remove water temperature regulator (7) and seal (9) from temperature regulator housing (6) .
Show/hide table
 | |
| Illustration 3 | g03419096 |
- Clean any lubricant from bore (8) .
- Remove lip seals (10) .
Show/hide table
 | |
| Illustration 4 | g03418903 |
Note: Note the orientation of the lip seals for installation purposes.
Installation Procedure
- Install water temperature regulator (7) in the reverse order of removal.
- Apply a thin layer of Tooling (A) to lip seal (10) and to bore (8) .
Caterpillar Information System:
C13 Generator Set Engine Water Pump - Remove and Install
3500 Engines Turbocharger - Install
3500 Engines Turbocharger - Remove
C13 Generator Set Engine Exhaust Manifold - Remove and Install
C7.1 Industrial Engine Injector (Diesel Exhaust Fluid) - Replace
349F and 352F Excavators Leaving the Machine
C15 and C18 Engines for China On-Highway Phase IV Diagnostic Capabilities
2013/09/20 A New and Improved Switch and Contactor Are Used for the Jacket Water Heater Control on Certain 3512C Engines {1383, 1408, 1408}
C7.1 Industrial Engine Diesel Exhaust Fluid - Fill
2013/09/16 New Wiring Harness Film Is Used for the Pre-lubrication Pump on Certain G3500 Engines {1319, 1408}
3500 Engines Engine Oil Cooler - Assemble
3500 Engines Engine Oil Cooler - Disassemble
2013/12/19 A New Pre-Lube System Is Used On Certain 3508 Industrial Engines Used In Fire Pump Applications {1307, 1319}
2013/11/08 New V Band Clamps and Mounting Hardware Are Used on Certain 3512C Engines {1059, 1071, 7553}
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Solenoid Valves
CAT WDS OEM and 777F Off-Highway Truck/Tractor Water Delivery System Gear Pump (Charge) - Remove and Install
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Combined Function - Electric Control
Site Positioning Requirements for Cat® MineStar System Products {7605} Site Positioning Requirements for Cat® MineStar System Products {7605}
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Piston Pump (Water Delivery) - Remove and Install
C4.4 Industrial Engine Emissions Certification Film
3500 Engines Engine Oil Cooler - Remove
3500 Engines Engine Oil Cooler - Install
2013/09/02 A New Bolt and Washer that Improves Durability of the Idler Transfer Gear is Used on Certain TH48-E70 Petroleum Transmissions {1234}
Air Conditioning and Heating R134a for All Caterpillar Machines Automatic Temperature Control Panel Troubleshooting - 584 and 584HD Forwarders