Camshaft
Show/hide table
| |
| 图 1 | g03371573 |
Show/hide table
| 技术规格 - 383-1739 凸轮轴总成 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| A | - | - | 新凸轮轴上止推垫圈的槽尺寸为 |
| C | 2 | 4N-1650 定位销 | 定位销的延伸量为 |
| D | 2 | 5B-5821 定位销 | 定位销的延伸量为 |
| E | 2 | 128-5993 止推垫圈 | 新止推垫圈的厚度为 |
| F | - | - | 轴承轴颈的直径为 安装后凸轮轴轴承的孔径为 |
| 1 | 16 | 5P-0076 螺栓 | 拧紧至扭矩为 |
Show/hide table
| |
| 图 2 | g03371572 |
Show/hide table
| 项目 | 数量 | 零件 | 技术规格说明 |
| 使用以下步骤确定实际凸轮轴凸轮升程：
1. 测量凸轮轴凸轮高度 (H)。 2. 测量基圆 (J)。 3. 从凸轮轴凸轮高度值 (H) 中减去基圆 (J)。 二者之差就是实际凸轮轴凸角升程。 |
|||
| G | - | - | 规定的凸轮轴凸轮升程
进气凸轮为 喷油器凸轮为 排气凸轮为 |
Caterpillar Information System:
C9.3 Tier 4 Final Engines Cylinder Block Cover Group
C13, C15, and C18 Tier 4 Final Engines Manifold (Diesel Exhaust Fluid)
C4.4 and C7.1 Engines Injector Solenoid - Test
G3512H and G3516H Generator Set Engines Crankshaft Main Bearings - Remove and Install
C280 Marine Engines Engine Governing - Adjust
G3512H and G3516H Generator Set Engines Gear Group (Rear) - Remove and Install
G3512H and G3516H Generator Set Engines Flywheel Housing - Remove and Install
G3512H and G3516H Generator Set Engines Crankshaft Rear Seal and Wear Sleeve - Remove and Install
G3512H and G3516H Generator Set Engines Crankshaft Front Seal and Wear Sleeve - Remove and Install
C280-16 Generator Set Engine for Nuclear Applications Speed Control
G3512H and G3516H Generator Set Engines Rocker Shaft and Push Rod - Remove and Install
C280-16 Generator Set Engine for Nuclear Applications Engine Speed/Timing Sensor
G3512H and G3516H Generator Set Engines Pistons and Connecting Rods - Remove and Install
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Electronic Service Tools
2013/11/25 A New Heavy-Duty Aftercooler is Available for Certain C32 Commercial Marine Engines Operating in Seawater {1063}
G3512H and G3516H Generator Set Engines Cylinder Liner - Remove and Install
3512B and 3512C Petroleum Generator Set Engines Air Cleaner
G3512H and G3516H Generator Set Engines Camshaft - Remove and Install
Bench Test Procedure for a CX48-P2300 Transmission {0599, 0717, 3003, 3030, 3101, 3159} Bench Test Procedure for a CX48-P2300 Transmission {0599, 0717, 3003, 3030, 3101, 3159}
3500 Engines Exhaust Elbow
2013/04/25 Clarification Of The Service Interval For The Connecting Rod Bearings For Certain C175-16 Marine Engines {1219}
G3512H and G3516H Generator Set Engines Crankshaft - Remove and Install
G3512H and G3516H Generator Set Engines Prelubrication Oil Pump - Remove and Install
G3512H and G3516H Generator Set Engines Engine Oil Pump - Remove and Install