Generator Coupling
Show/hide table
Illustration 1 | g03345223 |
Show/hide table
Specification for 276-4839 Generator Installation Ar     | |||
Item     | Qty     | Part     | Specification Description     |
1     | 12     | 7X-2575 Bolt     | Torque to 710 ± 60 N·m (524 ± 44 lb ft).     |
2     | As required, use the following shims:     | ||
4 | 137-8533 Shim Pack     | 137-8533 Shim Pack consists of following shims:     | |
Thickness of 137-8534 Shim is 0.0254 mm (0.00100 inch). |
|||
Thickness of 137-8535 Shim is 0.0508 mm (0.00200 inch). |
|||
Thickness of 137-8536 Shim is 0.0762 mm (0.00300 inch). |
|||
Thickness of 137-8537 Shim is 0.1016 mm (0.00400 inch). |
|||
Thickness of 137-8538 Shim is 0.12 mm (0.005 inch). |
|||
Thickness of 137-8539 Shim is 0.254 mm (0.0100 inch). |
|||
Thickness of 137-8540 Shim is 0.381 mm (0.0150 inch). |
|||
Thickness of 137-8541 Shim is 0.508 mm (0.0200 inch). |
|||
Thickness of 137-8542 Shim is 0.635 mm (0.0250 inch). |
|||
Thickness of 137-8543 Shim is 1.27 mm (0.050 inch). |
|||
Thickness of 137-8544 Shim is 1.91 mm (0.075 inch) |
|||
Thickness of 137-8545 Shim is 2.54 mm (0.100 inch). |
|||
Thickness of 137-8546 Shim is 3.05 mm (0.120 inch). |
Caterpillar Information System:
3500B Generator Set Engines Generator Coupling
3500B Generator Set Engines Turbocharger
C9.3B Engines Flywheel Housing Cover
C9.3 Engines for Caterpillar Built Machines Catalyst (SCR) - Remove and Install
C7.1 Marine Engine Connecting Rod Bearings - Remove and Install - Connecting rods in position
C7.1 Marine Engine Pistons and Connecting Rods - Assemble
C7.1 Marine Engine Pistons and Connecting Rods - Disassemble
C7.1 Marine Engine Pistons and Connecting Rods - Remove and Install
2013/02/27 A New Bracket Is Available for Certain C18 Marine Engines Equipped with Right Hand Service Duplex Fuel Filter Arrangements {1261}
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Configuration Parameters
C18 Industrial Engine Injector Solenoid - Test
C32 Generator Set Declaration of Conformity
C4.4 Industrial Engine Alarms and Shutoffs
C27 Generator Set Declaration of Conformity
C7.1 Engines for Caterpillar Built Machines Gear Group (Front)
CG137 Engines Crank But Do Not Start{1000} CG137 Engines Crank But Do Not Start{1000}
C27 Generator Set Safety Messages
C280-16 Engine Model View Illustrations
NOx Sensors Handling and Installation Procedures {191N} NOx Sensors Handling and Installation Procedures {191N}
2013/02/11 Updating the Fuel Filter Group on Certain C27 and C32 Industrial Engines {1261, 1262}
C280-16 Engine Safety Messages
C175-16 Locomotive Engine Coolant Temperature Is High
C7.1 Marine Engine Inlet Manifold - Remove and Install
C7.1 Marine Engine Exhaust Manifold - Remove and Install