Turbocharger
Show/hide table
 | |
| Illustration 1 | g03345208 |
Show/hide table
| Specification for 322-1928 Turbocharger Gp | |||
| Item | Qty | Part | Specification description |
| 1 | 16 | 2N-2765 High Temperature Bolt | Before assembly, apply Loctite C5A Copper anti-seize to the threads and the bearing surfaces. Torque to 55 ± 10 N·m (41 ± 7 lb ft). |
| 2 | 4 | 7W-2297 Clamp As | Use the following procedure to tighten the clamp assemblies: 1. Tighten the clamp assemblies to 14.0 ± 1.5 N·m (123.9 ± 13.3 lb in). 2. Gently hit around the clamp assemblies with a soft hammer. 3. Again, tighten the clamp assemblies to 14.0 ± 1.5 N·m (123.9 ± 13.3 lb in). |
| 3 | 4 | 9N-2038 Turbine Clamp As | Use the following procedure to tighten the turbine clamp assemblies: 1. Tighten the turbine clamp assemblies to 14.0 ± 1.5 N·m (123.9 ± 13.3 lb in). 2. Gently hit around the turbine clamp assemblies with a soft hammer. 3. Again, tighten the turbine clamp assemblies to 14.0 ± 1.5 N·m (123.9 ± 13.3 lb in). |
| 4 | 4 | 6L-3005 Band Clamp | Use the following procedure to tighten the band clamp: 1. Tighten the band clamp to 9.5 ± 1.0 N·m (84.1 ± 8.9 lb in). 2. Gently hit around the band clamp with a soft hammer. 3. Again, tighten the band clamp to 9.5 ± 1.0 N·m (84.1 ± 8.9 lb in). |
Caterpillar Information System:
C9.3B Engines Flywheel Housing Cover
C9.3 Engines for Caterpillar Built Machines Catalyst (SCR) - Remove and Install
C7.1 Marine Engine Connecting Rod Bearings - Remove and Install - Connecting rods in position
C7.1 Marine Engine Pistons and Connecting Rods - Assemble
C7.1 Marine Engine Pistons and Connecting Rods - Disassemble
C7.1 Marine Engine Pistons and Connecting Rods - Remove and Install
2013/02/27 A New Bracket Is Available for Certain C18 Marine Engines Equipped with Right Hand Service Duplex Fuel Filter Arrangements {1261}
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Configuration Parameters
C18 Industrial Engine Injector Solenoid - Test
C32 Generator Set Declaration of Conformity
C11, C13, C15, and C18 Industrial Engines Ether Starting Aid - Test
C18 Industrial Engine Electrical Power Supply - Test
3500B Generator Set Engines Generator Coupling
3500B Generator Set Engines Generator Coupling
C4.4 Industrial Engine Alarms and Shutoffs
C27 Generator Set Declaration of Conformity
C7.1 Engines for Caterpillar Built Machines Gear Group (Front)
CG137 Engines Crank But Do Not Start{1000} CG137 Engines Crank But Do Not Start{1000}
C27 Generator Set Safety Messages
C280-16 Engine Model View Illustrations
NOx Sensors Handling and Installation Procedures {191N} NOx Sensors Handling and Installation Procedures {191N}
2013/02/11 Updating the Fuel Filter Group on Certain C27 and C32 Industrial Engines {1261, 1262}
C280-16 Engine Safety Messages
C175-16 Locomotive Engine Coolant Temperature Is High