Engine Oil and Water Pump Drive - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1P-0520 | Driver Group | 1 |
Note: Check the O-ring seals for wear or damage. Replace the O-ring seals, if necessary.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Lower the temperature of bearing (11). Use Tooling (A) and a suitable press to install bearing (11) in front adapter assembly (12). The bore in bearing (11) must be
75.00 ± 0.06 mm (2.953 ± 0.002 inch) after installation. - Install O-ring seal (13).
Show/hide table
Illustration 2 g00921574 - Install gears (8) and (10) on shaft assembly (1).
- Install bolts (9).
Show/hide table
Illustration 3 g00921559 - Lower the temperature of bearing (5). Align the oil hole in bearing (5) with the oil hole that is in rear adapter assembly (3). Use Tooling (A) and a suitable press to install bearing (5).
- Ensure that bearing (5) does not extend above the surface of rear adapter assembly (3). The bore in bearing (5) must be
75.00 ± 0.06 mm (2.953 ± 0.002 inch) after installation. - Install O-ring seals (6) and (7) on rear adapter assembly (3).
Show/hide table
Illustration 4 g01052078 - Install rear adapter assembly (3) on shaft assembly (1).
- Install bolts and thrust washers (2).
- Install O-ring seal (4) on rear adapter assembly (3).
Show/hide table
Illustration 1 | g00921575 |
End By:
- Install the engine oil and water pump drive. Refer to Disassembly and Assembly, "Engine Oil and Water Pump Drive - Install".
Caterpillar Information System:
C18 Marine Engine Sensors and Electrical Components
C280-16 Petroleum Engine Turbocharger
C280-16 Petroleum Engine Water Temperature Regulator
C280-16 Petroleum Engine Fuel Injector
C280-16 Petroleum Engine Cylinder Head, Valves, Valve Springs and Valve Seat Inserts
C280-16 Petroleum Engine Aftercooler
C280-16 Petroleum Engine Engine Oil Lines (Prelubrication)
C280-16 Petroleum Engine Engine Oil Lines (Centrifugal Filter)
C32 Marine Engines Water Temperature Regulator - Remove and Install
2012/12/19 A New Pyrometer Is Available For Certain 3500 and G3500 Engines {7451, 7466, 7490}
C18 Marine Engine Aftercooler Condensate Drain Valve - Inspect/Clean
C32 Marine Engines Water Pump - Install
3516B Engine Engine Oil and Water Pump Drive - Install
C280-16 Petroleum Engine Camshaft Bearing Position
C18 Marine Auxiliary and Marine Generator Set Engines ECM Does Not Communicate with Other Modules
G3520E Generator Set Engines EPG Circuit Breaker - Test
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System - Set
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System - Calibrate
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Pressure Sensor - Calibrate
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System Accuracy - Test
Exciter Rotor Is Loosening on Certain 3512, and C32 Generator Sets{4454} Exciter Rotor Is Loosening on Certain 3512, and C32 Generator Sets{4454}
C18 Marine Engine Coolant - Change
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Timing - Calibrate
3516B Engine Engine Oil Scavenge Pump - Disassemble