Turbocharger
Show/hide table
Illustration 1 | g03779342 |
Show/hide table
Specification for 362-8652 Turbocharger Gp | |||
Item | Qty | Part | Specification Description |
1 | 18 | 5A-3604 Bolt | Before assembly, apply green Loctite 648 to the threads.
Torque to |
2 | 6 | 163-5495 Lockwasher Set | Torque to |
3 | 1 | 163-5497 Screw | Before assembly, apply green Loctite 648 to the threads. |
4 | 1 | 364-2150 Compressor Wheel | Before assembly, apply Loctite C5A copper anti-seize to the threads.
Torque to |
5 | 6 | 163-6443 Bolt | Before assembly, apply green Loctite 648 to the threads.
Torque to |
6 | 1 | 200-8029 Speed Sensor Gp | Torque to |
7 | - | - | Apply Before assembly, apply black Loctite 593 to the bearing housing. Assemble outlet housing to bearing housing within 5 minutes of applying the sealant. Sealant must be cured for minimum 2 hours before turbocharge is put into service. |
Show/hide table
Illustration 2 | g03779344 |
Housing assembly |
Show/hide table
Item | Qty | Part | Specification Description |
8 | 4 | 164-5070 Plug | Torque to |
9 | 7 | 8T-4244 Nut | Torque to |
Show/hide table
Illustration 3 | g03779347 |
164-5328 Inlet Housing |
Show/hide table
Item | Qty | Part | Specification Description |
10 | 9 | 191-8920 Bolt | Before assembly, apply Loctite C5A copper anti-seize to the threads. |
Show/hide table
Illustration 4 | g03779338 |
258-7579 Turbocharger Oil Lines Gp |
Show/hide table
Item | Qty | Part | Specification Description |
11 | 9 | 191-8920 Bolt | Before assembly, apply Loctite C5A copper anti-seize to the threads. |
Caterpillar Information System:
C280-16 Petroleum Engine Water Temperature Regulator
C280-16 Petroleum Engine Fuel Injector
C280-16 Petroleum Engine Cylinder Head, Valves, Valve Springs and Valve Seat Inserts
C280-16 Petroleum Engine Aftercooler
C280-16 Petroleum Engine Engine Oil Lines (Prelubrication)
C280-16 Petroleum Engine Engine Oil Lines (Centrifugal Filter)
C32 Marine Engines Water Temperature Regulator - Remove and Install
2012/12/19 A New Pyrometer Is Available For Certain 3500 and G3500 Engines {7451, 7466, 7490}
C18 Marine Engine Aftercooler Condensate Drain Valve - Inspect/Clean
C32 Marine Engines Water Pump - Install
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Connector Locations
C18 Marine Auxiliary and Marine Generator Set Engines Fuel System Pressure - Test
C18 Marine Engine Sensors and Electrical Components
3516B Engine Engine Oil and Water Pump Drive - Assemble
3516B Engine Engine Oil and Water Pump Drive - Install
C280-16 Petroleum Engine Camshaft Bearing Position
C18 Marine Auxiliary and Marine Generator Set Engines ECM Does Not Communicate with Other Modules
G3520E Generator Set Engines EPG Circuit Breaker - Test
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System - Set
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System - Calibrate
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Pressure Sensor - Calibrate
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators System Accuracy - Test
Exciter Rotor Is Loosening on Certain 3512, and C32 Generator Sets{4454} Exciter Rotor Is Loosening on Certain 3512, and C32 Generator Sets{4454}
C18 Marine Engine Coolant - Change