Engine Oil Filter
Show/hide table
Illustration 1 | g03356504 |
Left side view |
Show/hide table
Specification for 123-6884 Engine Oil Filter Gp     | |||
Item     | Qty     | Part     | Specification Description     |
1 2     |
2 2     |
0S-1571 Bolt 0S-1594 Bolt     |
Use the following bolt tightening sequence in order to tighten the clamp bolts: Snug the clamp assembly to the tube. Tighten the clamp assembly to the elbow. Tighten the clamp assembly to the tube. Tighten bolts to 47 ± 9 N·m (35 ± 7 lb ft).     |
3     | 1     | 8C-3446 Fluid Sampling Valve     | Torque to 11 to 13 N·m (97 to 115 lb in).     |
4 5     |
2 2     |
0S-1594 Bolt 0S-1571 Bolt     |
Use the following bolt tightening sequence in order to tighten the clamp bolts: Snug the clamp assembly to the tube. Tighten the clamp assembly to the elbow. Tighten the clamp assembly to the tube. Tighten bolts to 47 ± 9 N·m (35 ± 7 lb ft).     |
6     | 4     | 1P-1367 Plunger     | The bypass valve must move freely in the bore. Start to open pressure is 230 ± 20 kPa (33 ± 3 psi).     |
7     | 2     | 6V-5048 O-Ring Seal     | Lubricate the bore lightly with the lubricant being sealed.     |
8     | 4     | 7G-6713 Spring     | Length under test force is 57.2 mm (2.25 inch). Test force is 109 ± 5 N (25 ± 1 lb). Free length after test is 99.7 mm (3.93 inch).     |
Show/hide table
Illustration 2 | g03356506 |
Show/hide table
Specification for 123-6884 Engine Oil Filter Gp     | |||
Item     | Qty     | Part     | Specification Description     |
9     | 2     | 2P-4304 Hollow Stud     | Apply red Loctite 271 on the tapered end of the hollow stud to the length (C) of 10.2 ± 1.5 mm (0.40 ± 0.06 inch).     |
Torque to 80 ± 14 N·m (59 ± 10 lb ft). |
Caterpillar Information System:
G3500 Generator Sets Fuel Filter Differential Pressure - Check
3512C and 3516C Marine Propulsion Engines Synchronization Problem
G3500 Generator Sets Engine Air Cleaner Element (Single Element) - Inspect/Replace
3516B Engine for the MT4400D Off-Highway Truck Water Lines
3516B Engine for the MT4400D Off-Highway Truck Water Lines
G3500 Generator Sets Coolant Temperature Regulator - Replace
G3516C and G3516E Gas Engines Water Lines
C7.1 Industrial Engine Plate Locations and Film Locations
G3500 Generator Sets Coolant Sample (Level 2) - Obtain
C7.1 Industrial Engine Plate Locations and Film Locations - Aftertreatment System
3516B Engine for the MT4400D Off-Highway Truck Accessory Drive - Air Conditioner Compressor
C18 Marine Engines Engine Oil Filter Base - Remove and Install
3516B Engine for the MT4400D Off-Highway Truck Flywheel Housing Cover
3516B Engine for the MT4400D Off-Highway Truck Fuel Injection Lines
2012/05/23 New Cylinder Head Gasket on Certain 3044C and C3.4 Engines {1100, 1100, 7555}
320E and 323E Excavators Engine and Machine Warm-Up
G3500 Engines Product Lifting
C18 Marine Engines Engine Oil Pump - Remove and Install
C7.1-XQ200 Rental Generator Set Belts - Inspect/Adjust/Replace
C18 Marine Engines Engine Support (Front) - Remove and Install
3512C and 3516C Marine Engines Electronic Control Module (ECM)
C18 Marine Engines Flywheel - Remove and Install
C18 Marine Engines Crankshaft Rear Seal - Remove and Install
C18 Marine Engines Flywheel Housing - Remove and Install