Engine Oil Filter Base - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 187-2718 | Filter Wrench | 1 |
| B | - | LOCTITE 263 | - |
| - | LOCTITE 270(1) | - | |
Show/hide table
| (1) | Europe Only |
- Use Tooling (A) to remove engine oil filters (1).
- Disconnect the harness assembly to sampling valve (3). Remove sampling valve (3) and the adapters.
- Remove bolts (2).
Show/hide table
Illustration 2 g03046517 - Position engine oil level gauge (5) out of the way.
- Remove clip (7).
- Remove bolts (4). Remove engine oil filter base assembly (6) from the oil manifold. Discard the gasket. Replace with a new gasket for installation.
Show/hide table
Illustration 3 g03046596 Show/hide table
Illustration 4 g03046640 Note: Elbow (8) has an integral seal. The integral seal may have remained with the oil manifold, or came off with the removal of the engine oil filter base assembly. Discard the integral seal and replace with a new integral seal for installation.
- Remove elbow (8) and discard the O-ring seal. Replace with a new O-ring seal for installation.
- Remove nuts (10) and remove engine oil filter base (9). Remove studs (11).
Show/hide table
Illustration 5 g03046642 - Remove hollow stud (12), purge screw (13), and shutoff valve (16).
- Remove bolts (15). Remove cover (14) and discard the gasket. Replace with a new gasket for installation.
- Repeat Step 8 through Step 10 for the remaining engine oil filter base.
Show/hide table
| |
| Illustration 1 | g03046477 |
- Install engine oil filter base (9) in the reverse order of removal.
- Tighten purge screw (13) to a torque of
12.7 ± 2 N·m (112 ± 18 lb in) .Show/hide table
Illustration 6 g03046776 - Apply Tooling (B) to the threads of hollow stud (12) along the length of Area (X). The length of Area (X) is
10.2 ± 1.5 mm (0.40 ± 0.06 inch) . - Tighten hollow stud (12) to a torque of
80 ± 14 N·m (59 ± 10 lb ft) . - Tighten studs (11) to a torque of
35 ± 5 N·m (26 ± 4 lb ft) . - Lubricate the bore for elbow (8) and the O-ring seal with the fluid that is being sealed.
- Tighten sampling valve to a torque of
10 ± 2 N·m (89 ± 18 lb in) . - Apply clean engine oil to the seal for engine oil filters (1). Tighten engine oil filters (1) one full turn after the seal contacts the engine oil filter base.
- Tighten purge screw (13) to a torque of
Caterpillar Information System:
2012/05/21 Cat® Electronic Technician (Cat® ET) Improved for Configuring of Annunciator Alarm Module on Certain Cat® Products {0785, 7400}
G3500 Generator Sets Coolant Level - Check
14M Series 3 Motor Grader Brakes, Indicators and Gauges - Test
3516B Engine for the MT4400D Off-Highway Truck Auxiliary Drive (Lower Left Hand)
G3500 Generator Sets Coolant (NGEC) - Change
C9.3 Tier 4 Final Engines Sensor Signal (Analog, Active) - Test
G3500 Generator Sets Coolant (DEAC) - Change
3516B Engine for the MT4400D Off-Highway Truck Flywheel
G3500 Engines Engine Oil Filter
G3516C and G3516E Gas Engines Water Pump
C7.1 Industrial Engine Product Description - Engine and Aftertreatment
G3512E Generator Set Engines Engine Oil Pan
3516B Engine for the MT4400D Off-Highway Truck Accessory Drive - Air Conditioner Compressor
C7.1 Industrial Engine Plate Locations and Film Locations - Aftertreatment System
G3500 Generator Sets Coolant Sample (Level 2) - Obtain
C7.1 Industrial Engine Plate Locations and Film Locations
G3516C and G3516E Gas Engines Water Lines
G3500 Generator Sets Coolant Temperature Regulator - Replace
3516B Engine for the MT4400D Off-Highway Truck Water Lines
3516B Engine for the MT4400D Off-Highway Truck Water Lines
G3500 Generator Sets Engine Air Cleaner Element (Single Element) - Inspect/Replace
3512C and 3516C Marine Propulsion Engines Synchronization Problem
G3500 Generator Sets Fuel Filter Differential Pressure - Check
3516B Engine for the MT4400D Off-Highway Truck Engine Oil Filter