Torque Converter and Transmission Oil - Change
Show/hide table
 |
热油和热的部件可能会导致人员受伤。 不要让热的油和部件接触皮肤。 |
Show/hide table
| 注意 |
|---|
在进行检验、保养、测试、调整及维修产品期间，必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前，要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品，请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
注: 运转变速箱，直到变矩器和变速箱油温热。
- 取下通气孔盖 (1) ，防止从变速箱箱体排放机油时出现真空。
Show/hide table
 | |
| 图 1 | g02994977 |
右视图 (1) 通气孔盖 (2) 目测表 (3) 环保排放塞 | |
- 从变速箱底部拆下环保排放塞 (3) 。
- 将回油软管安装到环保排放口中，并将机油排放到适当的容器中。
注: 排放回转接头组件 176-6545 和软管可从 Cat 代理商处购买。
- 待机油从变速箱箱体排放完后，清洁环保排放塞。
- 从环保排放口上拆下排放软管。
- 安装环保排放塞并将其拧紧至 100 ± 20 N·m (74 ± 15 lb ft)。
- 向变速箱箱体加油。 参阅操作和保养手册, "润滑剂粘度"和操作和保养手册, "加注容量"。
- 确保变速箱处于空档位置。 盘车起动发动机 15 秒。 不要让发动机起动。
- 检查变速箱箱体侧面目测表 (2) 显示的油位。 重复步骤 7 至步骤 8，直到油位处在目测表 (2) "COLD（冷）"侧的 "ADD（添加）"标记和 "FULL（满）"标记之间。
- 安装通气孔盖 (1) 。
- 起动发动机并在低怠速下运转。 检查有无泄漏并进行必要的修理。
- 当油温热和变速箱在空档位置时，观察油位。
- 将油位保持在目测表 (2) "HOT（热）"侧的 "ADD（添加）"标记和 "FULL（满）"标记之间。
- 必要时停止发动机并加油。
Show/hide table
| 注意 |
|---|
换油后，不正确加注变速箱油箱可能引起变速箱离合器的损坏。 遵照上面描述的程序。 变速箱方向和速度操纵杆必须保留在空档（NEUTRAL），直到系统充满。 |
Caterpillar Information System:
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Oil Filter (Torque Converter, Transmission) - Replace
3512C and 3516C Marine Engines Auxiliary Drive Shaft
C13, C15, and C18 Tier 4 Final Engines Mounting Frame
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Magnetic Screen (Transmission) - Clean
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Breather (Transmission) - Clean
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Capacities (Refill)
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Lubricant Viscosities
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Lifting and Tying Down the Transmission
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201} Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
C4.4 Marine Generator Set Space Heater - Test
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Transmission Operation
C4.4 Marine Generator Set Rotating Rectifier - Inspect/Test
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Torque Converter and Transmission Oil Level - Check
2012/04/17 A New Holder for the Flywheel Timing Pin is Used On C175-16 Petroleum Engines {1157}
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Torque Converter and Transmission Oil Sample - Obtain
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Reference Material
2014/07/11 An Improved Front Crankshaft Seal Is Used on G3300 Engines {1160, 1161}
3512C and 3516C Marine Engines Auxiliary Water Pump
320E and 323E Excavators Machine System Specifications Pilot Lines
C4.4 Marine Generator Set Turbocharger - Inspect
C4.4 Marine Generator Set Engine Air Cleaner Element (Single Element) - Inspect/Replace
C3.4B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C4.4 Marine Generator Set Product Storage
3116 and 3126 Marine Engines Maintenance Interval Schedule