Oil Filter (Torque Converter, Transmission) - Replace
Show/hide table
 |
热油和热的部件可能会导致人员受伤。 不要让热的油和部件接触皮肤。 |
Show/hide table
| 注意 |
|---|
在进行检验、保养、测试、调整及维修产品期间，必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前，要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品，请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 拆下滤清器壳体底部的排放塞 (5) 和密封件。 让滤清器壳体的机油排放到适当的容器内。
Show/hide table
 | |
| 图 1 | g02994356 |
变速箱油滤清器 (A) 和 (B) | |
Show/hide table
 | |
| 图 2 | g02994904 |
拆解机油滤清器 (1) 机油滤清器座 (2) 密封件 (3) 机油滤清器滤芯 (4) 机油滤清器壳体 (5) 排放塞 | |
- 拆下机油滤清器壳体 (4) 。 废弃机油滤清器壳体 (4) 内旧的机油滤清器滤芯 (3) 。 拆下滤清器时将会排出剩余的机油。 将机油排放到适当的容器中。
- 检查机油滤清器座 (1) 上的密封件 (2) 。 如果油封损坏，用新的油封更换。
- 将新的机油滤清器滤芯 (3) 安装到机油滤清器壳体 (4) 中。
- 将机油滤清器壳体 (4) 和新的滤芯 (3) 安装到滤清器座 (1) 中。 将壳体拧紧至扭矩为 75 ± 5 N·m (55 ± 4 lb ft)。 不要使用气动扳手拧紧。
- 将排放塞 (5) 和密封件安装到滤清器壳体中。 将排放塞 (5) 拧紧至扭矩为 37 ± 2 N·m (27 ± 2 lb ft)。
- 确保变速箱处于空档 。 起动发动机并以低怠速运转发动机。 检查有无泄漏并进行必要的修理。
- 当油温热和变速箱在空档位置时，观察油位。
- 关闭发动机。 如有必要，加注机油。
Caterpillar Information System:
3512C and 3516C Marine Engines Auxiliary Drive Shaft
C13, C15, and C18 Tier 4 Final Engines Mounting Frame
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Magnetic Screen (Transmission) - Clean
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Breather (Transmission) - Clean
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Capacities (Refill)
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Lubricant Viscosities
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Lifting and Tying Down the Transmission
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201} Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
C4.4 Marine Generator Set Space Heater - Test
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Transmission Operation
C4.4 Marine Generator Set Rotating Rectifier - Inspect/Test
2012/04/17 An Improved Front Crankshaft Seal is Used on Certain 3306B Engines {1160, 1161}
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Torque Converter and Transmission Oil - Change
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Torque Converter and Transmission Oil Level - Check
2012/04/17 A New Holder for the Flywheel Timing Pin is Used On C175-16 Petroleum Engines {1157}
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Torque Converter and Transmission Oil Sample - Obtain
CX48-P2300-3512 Petroleum Power Train Package and CX48-P2300 Petroleum Transmission Transmission Reference Material
2014/07/11 An Improved Front Crankshaft Seal Is Used on G3300 Engines {1160, 1161}
3512C and 3516C Marine Engines Auxiliary Water Pump
320E and 323E Excavators Machine System Specifications Pilot Lines
C4.4 Marine Generator Set Turbocharger - Inspect
C4.4 Marine Generator Set Engine Air Cleaner Element (Single Element) - Inspect/Replace
C3.4B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
C4.4 Marine Generator Set Product Storage