Fuel Transfer Pump
Show/hide table
| |
| Illustration 1 | g01430288 |
|
(1) Inlet port
(2) Pressure regulating valve (3) Outlet port (4) Drain hole | |
When the fuel transfer pump is using diesel fuel, the fuel transfer pump has the following specifications.
Run the pump at 2940 rpm. The full bypass pressure should be the following value. ...
Run the pump at 840 rpm. The flow at
Run the pump at 120 rpm with a blocked inlet for 30 seconds. The pump inlet must have a suction lift of
Run the pump at 2940 rpm. The flow at
When the pump is viewed from the drive end, the rotation of the pump is counterclockwise.
Caterpillar Information System:
G3500 Engines Actuator Linkage - Air/Fuel Ratio Control
370-8571 Bulk Fuel Filtration Group 300 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280} 370-8571 Bulk Fuel Filtration Group 300 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
316E Excavator Machine System Specifications Window Wiper and Washer - Lower
316E Excavator Machine System Specifications Window Wiper - Front, Upper
149-7173 Bearing Handling Bracket Assembly {0374, 0599, 0629, 0632, 4006, 4008, 7551} 149-7173 Bearing Handling Bracket Assembly {0374, 0599, 0629, 0632, 4006, 4008, 7551}
2012/02/07 New O-rings Are Now Used on Certain C27 / C32 Commercial Oil Pan Groups {1302}
320E and 323E Excavators Machine System Specifications Stick Lines
3516C Generator Sets Control Panel - Inspect/Test
307E2 Mini Hydraulic Excavator Machine System Specifications Blade Lift Cylinder
Initial Start-Up Procedure for CG137 and G3300B Engines {1000} Initial Start-Up Procedure for CG137 and G3300B Engines {1000}
362-0960 Lifting Beam Assembly {0599, 0629, 0700, 0729, 0757, 1122} 362-0960 Lifting Beam Assembly {0599, 0629, 0700, 0729, 0757, 1122}
3516C Generator Set Engines Turbocharger Turbine Temperature Is High
2011/10/31 A New Hose Assembly Is Used for the Duplex Fuel Filters on Certain 3516B Engines {1261}
Using the Inspection Head (ISH) Ultrasonic Reader for G3600, 3600, and C280 Connecting Rod Bolts{0769, 1218} Using the Inspection Head (ISH) Ultrasonic Reader for G3600, 3600, and C280 Connecting Rod Bolts{0769, 1218}
C13 Engine for Combat and Tactical Vehicles Cylinder Head Valves
2011/10/31 Improved Bolts Are Used for the High-Pressure Fuel Pump Relief Valve on C175-16 Engines {1251, 7553}
2011/10/31 An Improved Inlet Manifold Pressure Sensor Is Used with Certain G3516C and G3520C Generator Set Engines {1408, 1439, 1917}
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators Connector Contact Description
3500 Generator Sets Refill Capacities
2011/11/14 Hydraulic Control Modifications for TH48-E80 Petroleum Transmission and SPF343C Pumper Transmission {3074, 3083, 3167}
2011/11/03 An Improved Coupler is Used on Certain Petroleum Transmissions {3252}
3516C Generator Set Engines Data Link - Test
Cat® Grade Control Depth & Slope for E-Series and F-Series Excavators Machine Dimensions - Configure
3500C Marine Engines Monitoring System - Diagnostic Codes and Event Codes